What is the azeotrope pressure and composition

Assignment Help Mechanical Engineering
Reference no: EM13718060

In the system A + B activity coefficients can be expressed by the one-parameter Margules equation with A=0.5. The vapor pressures of A and B at T=80C are 900mmHg and 600mmHg respectively. Is there an azeotrope in this system at T=80C and if so, what is the azeotrope pressure and composition

Reference no: EM13718060

Questions Cloud

Change in specific entropy between two specified states : Using the appropriate table, determine the change in specific entropy between the two specified states, in Btu/lb.oR. Show the states on a sketch of the T-s diagram.
Determine the indicated property : Using the appropriate table, determine the indicated property. In each case, locate the state on sketches of the T-v and T-s diagrams. Include the vapor dome on the diagram.
Sheet of cold worked copper has a ductility : A sheet of cold worked copper has a ductility of 15%. If the sheet thickness is 3.4 mm, what were the dimensions of the cross-section before rolling?
Benefit of the use of antimicrobial drugs : Present the comparison of clinical benefit of the use of antimicrobial drugs. What criteria are used for selection and for monitoring of the use of antimicrobial drugs?
What is the azeotrope pressure and composition : In the system A + B activity coefficients can be expressed by the one-parameter Margules equation with A=0.5. The vapor pressures of A and B at T=80C are 900mmHg and 600mmHg respectively. Is there an azeotrope in this system at T=80C and if so, what ..
What is the new value of keff : A certain u-235 fueled pressurized water reactor is just critical. Suddenly the average coolant temperature falls from 300c to 280c \alphat=-0.0001 \deltak/c. How much reactivity is inserted? What is the new value of keff?
Describe absorption process of products of lipid digestion : Describe the major mechanisms for stimulation of gastric acid secretion and inhibition in cephalic, gastric and intestinal phases and describe the absorption process of the products of lipid digestion.
Ammonia enters a valve as saturated liquid : Ammonia enters a valve as saturated liquid at 9 bar and undergoes a throttling process to a pressure of 2 bar. Determine the rate of entropy production per unit mass of ammonia flowing, in kW/(kg·K). If the valve were replaced by a power-recovery tu..
Assuming a constant specific heat for the cooling water : A refrigeration unit operating on R-134a is used to maintain a freezer at -15°C. The refrigeration unit operates at a suction pressure of 140kPa and a discharge pressure of 900kPa. The condenser of the refrigeration unit is cooled by a water cooled h..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd