What is the axial stress in the wall of the tank

Assignment Help Mechanical Engineering
Reference no: EM131062175

A tall standpipe with an open top (see figure) has diameter d = 2.2 m and wall thickness t = 20 mm.

(a) What height h of water will produce a circumferential stress of 12 MPa in the wall of the standpipe?

(b) What is the axial stress in the wall of the tank due to the water pressure?

2351_8f415bc2-011b-4dc1-beab-8b1d5ec74059.png

Reference no: EM131062175

Questions Cloud

What is the maximum data transfer rate : What is the storage capacity of the disk? What is the maximum data transfer rate (bytes/second)? What is the maximum rotational delay? What is the transfer time?
What is the factor of safety n against tearing : If the longitudinal seam along the ridge tears open when it is subjected to a tensile load of 540 pounds per inch of seam, what is the factor of safety n against tearing when the internal pressure is 0.5 psi and the structure is fully inflated?
Verb of the fourth amendment : The right of the people to be secure in their persons, houses, papers, and effects, against unreasonable searches and seizures, shall not be violated, and no Warrants shall issue, but upon probable cause, supported by Oath or affirmation, and part..
Discuss how risk might be dealt with peck model : Discuss how risk might be dealt with in levels 1, 2 and 3 of Peck's model of the supply chain
What is the axial stress in the wall of the tank : What is the axial stress in the wall of the tank due to the water pressure?
Credibility of a wikipedia article : How is the credibility of a Wikipedia article different from that of a published research paper? Which resource do you think is more reliable or more useful? Is it reasonable to quote a Wikipedia article in your research essay? If you consult Wiki..
Impact on fiction in contemporary literature : Have any more recent events had a similar impact on fiction in contemporary literature? If so, which events? What impact have they had? And which works exemplify this impact for you?
Change depending on the genre and the era : How comfortable are you in determining the quality of literature? Do you find it easy to critique a text? If not, what do find difficult? How does your comfort level change depending on the genre and the era in which the text was written?
Evaluate the main points of the reading : Summarize, explain, and evaluate the main points of the reading at the end of Chapter 1- "How to Make Our Ideas Clear" by Charles S. Peirce in a minimum of 3 paragraphs. Do not simply cut and paste from the reading,

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd