What is the axial force in member hj

Assignment Help Civil Engineering
Reference no: EM13211293

The frame shown is used to support high-tension wires. If W = 200 lb, b = 3 ft, a = 30°, what is the axial force in member HJ?

Reference no: EM13211293

Questions Cloud

What is the over consolidation ratio of the soil : an increment of vertical stress of 150kpa compress the sample to a void ratio of1.43. what is the over consolidation ratio of the soil at the unloaded condition.
What is correlation coefficient between two securities : Standard deviation of stock A is 10% and that of stock B is 20%, what is the correlation coefficient between the two securities?
Humanist movement began : What was the traditional (Catholic) view of man's position in the universe when the Humanist Movement began? "
Where a major earthquake has happened in the past, : Where a major earthquake has happened in the past, but not in a while is called a seismic...
What is the axial force in member hj : The frame shown is used to support high-tension wires. If W = 200 lb, b = 3 ft, a = 30°, what is the axial force in member HJ?
Why each of these groups missed out on the good times : Identify the groups that did not share in the general prosperity of Americans during the 1950s. Explain why each of these groups missed out on the “good times.”
Desribe the historial development of police agencies : Desribe the historial development of police agencies and their jurisdiction.
State the dispersion of a diffraction grating : The dispersion of a diffraction grating, such as the one shown at the right, is the angle of separation per ?m of wavelength. It depends on the order of the diffraction (n),
Explain what judicial review : Explain what judicial review is and how it affects the federal government. How did the Supreme Court attain this power? is it fair? Why or why not?

Reviews

Write a Review

Civil Engineering Questions & Answers

  What is the rate of evapouration of water

what is the rate of evapouration of water from a reservoir with air temp at 20c and the surface of reservoir is 3000m2.

  Waterline of center of gravity

The ship has a total weight of 155,000 tons, length = 1,600 feet and a beam = 150 feet (assume that it is the shape of a rectangular box). Calculate the height above the waterline of its center of Gravity (G).

  Find the steel area required for beam

Find the steel area required for beam which has b = 10 in. and d = 17.5 in. to carry a factored load moment of 1,600 in-kips.

  Determine the couple m required to hold the system

the pin at B is attached to member ABC and can slide freely along the slot cut in the fixed plate. Neglecting the effect of friction, determine the couple M required to hold the system in equilibrium when.

  Construction area skids into a stack of concrete barriers

A car travelling at 60 mph in a construction area skids into a stack of concrete barriers. Skid marks leading to the crash measures 150 ft .

  What is the average velocity

hydrogen is flowing in a 50 mm diameter pipe at a mass rate of 0.01 kg/s. at section 1 the pressure is 280 kPa abs and t= 25 . what is the average velocity?

  Difference between dry and moist lapse rate

Explain how the desert air can contain much more h 2 o vapor in the air than the pole, and still a lower humidity than the pole? what causes the difference between dry and moist lapse rate?

  Determine the compression of each spring

The 75 lb block is released from rest 5 ft above the plate. Determine the compression of each spring when the block momentarily comes to rest after striking the plate.

  Determine the volume flow rate

Water with a static pressure of 1.96kN/M2 flows through an 800 mm diameter pipe. A pitot tube pressure gage in this pipe reads a pressure of 5.88 kN/M2. How do you determine the volume flow rate (Q) of the water? (Q = 1.40 M^3/sec, V=2.79 M/sec)

  Calculating the undrained shear strength

Calculate the undrained shear strength at a depth of 120 ft below the mudline. Calculate the undrained shear strength at a depth of 120 ft below the mudline if the soil has an OCR of 2.5 .

  Explain indicated concentrations of total volatile solids

Influent sample collected from a wastewater treatment plant was analyzed for various solids concentrations. Results indicated concentrations of Total Volatile Solids (TVS)

  Determine the reaction forces at points b and c

The fixture AC is designed with a screw adjustment to regulate the height of the 900 N load supported by the roller at A. The screw bears against a smooth surface at B. Determine the reaction forces at points B and C. Neglect the weight of the fix..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd