User Account

All Pages

What is the approximate real power

Assignment Help Electrical Engineering
Reference no: EM131756061

Questions -

Q1. In a series RLC circuit, we have a resistance of 1500Ω, an inductor rated at 1000μH, and a capacitor rated at 0.1μF. The supply voltage is 100V at 10kHz. Calculate the value of the total circuit impedance for the circuit and the resonant frequency of the circuit.

Q2. Calculate the total circuit impedance of a parallel RL circuit consisting of a 500Ω resistor and an inductor rated at 1500mH. The supply voltage is 50V at 500Hz.

Q3. In a certain balanced three-phase system, each line current is 10A and each line voltage is 240V. What is the approximate real power if the power factor is 0.75?

Q4. A DC generator with an efficiency of 92 percent has an output of 440 volts at 75 amperes. Calculate the machine power losses for this generator.

Q5. A battery containing five 12V at 1.5A cells connected in series has a total voltage and current of 60V, 1.5A. If these five cells were connected in parallel, what would be the total voltage and current?

Q6. A circuit consists of 4 capacitors in series with values of 0.15μF, 0.25μF, 0.4μF, and 0.5μF. Calculate the total capacitance of this series circuit. If we place a resistor of 50k/2 in series with this combination, what is the time constant of this circuit?

Q7. In a series RC circuit with a DC supply of 100 volts, at the third time constant, what would the measured value of the voltage be across the resistor and the capacitor?

Q8. A circuit consists of 4 inductors in series with values of 50μH, 100μH, 150μH, and 250μH. Calcuate the total inductance of this series circuit. If we place a resistor of 1000Ω in series with this combination, what is the time constant of this circuit?

Reference no: EM131756061

Questions Cloud

What gain or loss would be recognized on the called bonds : Didde Company issues $20,000,000 face value of bonds at 96 on January 1, 2013. The bonds are dated January 1, 2013, pay interest semiannually at 8%.
Little mikey''s catering ledger reflected a normal balance : Little Mikey's Catering ledger reflected a normal balance of $71,000 for accounts receivable
What grammar mistakes stand out the most to you : What grammar mistakes stand out the most to you? Think especially about sentence structure errors. List any other MLA formatting errors.
How much should crane record as the cost : How much should Crane record as the cost of the machine, Crane purchased the bonds to yield
What is the approximate real power : In a certain balanced three-phase system, each line current is 10A and each line voltage is 240V. What is the approximate real power
What does it mean for demand to be unitary : When a consumer does not have much personal experience with a realtor (for example, a first-time home buyer), he will form expectations from.
Prepare t-accounts for manufacturing overhead : Dillon Products manufactures various machined parts to customer specifications. The company uses a job-order costing system and applies overhead costs to jobs.
Develop an outline of the project plan for the testing : As part of the disaster recovery planning at any medium-sized business, you have been asked to develop a project plan to test the backup of production systems
How would you define irm : Please respond with a minimum of a two paragraph response

Reviews

len1756061

12/8/2017 2:25:32 AM

ESSAY INSTRUCTIONS: All of the questions on this examination are to be answered on the answer sheets provided. Write your name, your student number, and the appropriate module number or semester number at the top of each answer sheet. Be certain to indicate the proper question number before each of your answers. Remember to show your work if an answer requires a mathematical solution. If you need additional space, you may write on the back of the answer sheets.

Write a Review

Electrical Engineering Questions & Answers

  Calculate the external resistance to be added

The rotor of a 6-pole, 50 Hz slip ring induction motor has a resistance of 0.25 Ω/ phase and runs at 960 rpm. Calculate the external resistance/phase to be added to lower the speed to 800 rpm with load torque redcing to 3/4th of the previous value..

  The standard model of trade

Assume that Norway and Sweden trade with each other, with Norway exporting fish to Sweden, and Sweden exporting Volvos (automobiles) to Norway.

  How many sec are required for system to reach steady state

a. if the input r(t)=5u(t), ie. R(s)=5/s, find the steady-state of C(t), b. Approximately how many seconds are required for the system to reach steady state note you two time constants to consider, and c. Do you expect the transient response to be o..

  Find the equilibrium n and p values in the neutral regions

Doping is Nd=1x10^20/cm^3 on the n-side, and Na=1x10^18/cm^3 on the p-side. Find the equilibrium n and p values in the neutral regions on both sides as well as total depletion thickness in micrometer and peak electric field.

  Determine the maximum stress in the aluminum strip

A copper strip (Ec = 105 GPa) and an aluminum strip (Ea = 75 GPa) are bonded together to form the composite beam shown. Knowing that the beam is bent about a horizontal axis by a couple of moment M = 35 N.m,

  Find the surface temperature in k of the computer chip

For computer chip of 10mm (length), 5 mm(width) is operated by power of 0.645 watt, which surrounded by coolant material of temp of 80 F. Find the Surface Temperature in K of the computer chip during the heat transfer of convection.

  System to the inputs

Problems: 1. An LTI system whose response to the signal x(t) below is the signal y(t) below. Determine and sketch carefully the response of the system to the inputs xa(t) and xb(t) below using LTI properties.

  Calculate equivalent series impedance and resistance

The nameplate on a 50-MVA, 60-Hz single-phase transformer indicates that it has a voltage rating of 8.0-kV: 78-kV. An open-circuit test is conducted from the low-voltage side, and the corresponding instrument readings are 8.0kV, 62.1A, and 206kW.

  For the miller divider of figure determine the loop gain

For the Miller divider of Figure, determine the loop gain. Assume the tanks in the drains of M1 and M2 can be replaced by a resistance of RP at resonance.

  Determine magnetic flux density using mean radius of toroid

Assume the coil around the toroid is one single coil and extends all the way around. A toroid is like a donut with a circular cross section. The following characteristics are given: Toroid material = sheet steel, N = 250 turns Inner Radius

  What is the minimum resistance of a series resistor

A 12 V battery with a 0.3 internal resistance is to be charged froma 15 V source. If the charging current should not exceed 2 A, what is the minimum resistance of a series resistor that will limit thecurrent to this safe value

  What is the purpose of the astm standards

What is Standard 189.1-2009? What is the National Green Building Standard?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd