What is the air-fuel ratio

Assignment Help Mechanical Engineering
Reference no: EM13711576

A fuel consisting of 20% ethanol and 80% isooctane on a molar basis is burned with air in an engine

a) Write the balanced chemical reaction when this reaction is stoichiometric

b) What is the air-fuel ratio?

c) A dry exhaust analysis gives 11.7% CO  2 and 4.1% O   2. What is the equivalence ratio?

Reference no: EM13711576

Questions Cloud

Temperature drop during this process-final specific volume : Refrigerant-134a is throttled from saturated liquid state at 7 bar to a pressure of 1.4 bar. Determine the temperature drop during this process and the final specific volume.
Cauchys theorem for a triangle : The theorem stated below is followed by statements from its proof. For each of the numbered statements provide a short comment that explains or justifies it.
Steady flow operation and constant specific heat for water : A water fountain consume 24.1 amps (operating at 110 V) to chill water from 23 C to 5 C. It is known that heat is rejected from the unit at a rate of 9.5 kW. Assuming steady flow operation and constant specific heat for water (at 25 C)
Fraction of heat release at constant pressure conditions : A four cylinder, 3.6 litter CI engine operates with a compression ratio of 18 and an air fuel ratio of 17. The engine operates on a dual cycle. The maximum pressure is limited to 12MPa and the maximum temperature is limited to 3600 K. Assume that at ..
What is the air-fuel ratio : A fuel consisting of 20% ethanol and 80% isooctane on a molar basis is burned with air in an engine. Write the balanced chemical reaction when this reaction is stoichiometric. What is the air-fuel ratio?
What is the temperature of the exhaust gas : A 4 cylinder 1.6 liter SI engine has a compression ratio of 10, connecting rod length of 16.8cm, and a crank offset of 4.5 cm. The engine is operating at 3000 RPM and wide open throttle. The exhaust pressure is 100 kPa. The intake valve closes at 20 ..
Mixture temperature leaving the mixing chamber : In air-conditioning systems, streams of cold and warm air are mixed to get air with the right temperature. Consider a mixing chamber into which cold air enters at 8C and 100 kPa at a rate of 0.55 m^3 /s and warm air enters at 300C and 100 kPa. The ra..
Matlab code to calculate and plot the second explosion limit : Write a matlab code to calculate and plot the second explosion limit (2k1=k9[m] for the H2- air mixture with Phi=0.5 within temperature range of 500-1000k compare the line with the explosion limit in the textbook and see if they qualitatively agree. ..
Rooftop solar hot water heater with collector areas : A rooftop solar hot water heater with collector areas of 8 m2 and storage of 640 L is installed in Phoenix, Arizona on a house that uses 160 L/day of hot water at 60°C. 70% of the total energy required is supplied by solar energy (the solar fraction ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd