User Account

All Pages

What is the adt output for a temperature of 81 degrees

Assignment Help Electrical Engineering
Reference no: EM13229551

A HCS12 ATD is set to 10-bit unsigned mode. The voltage references are set to ground and 1.0V What is the ADT output for a temperature of 81 degrees? The temperature sensor measures 0 to 100 degrees with an output of 10 mV/degree.

Reference no: EM13229551

Questions Cloud

Explain how to recover the increased design cost : a cost to produce, P, of $4.00. If we were able to reduce this to $3.55 through greater attention in the design, and if the cost to improve the design (in NRE) is $35,000, how many units must we sell to recover the increased design cost
Examine the role of advertising and promotion management : Examine the role of advertising and promotion management in contemporary marketing and develop an understanding of integrated marketing communications, including the coordination of the various promotional mix elements
Find the reflection coefficient at the load : A 75- ohm lossless transmission line is interfaced to a load impedance that consists of a series connected resistor of 30 ohm and a capacitor of 10 pF. At an operating frequency of 2 GHz and for a wavelength of 10 cm.
Determine the total power in fm signal : An FM signal being transmitted is represented by eFM(t) = 50Sin((2)(95.1)(106)t+2Sin((2)(10)(103)t)). If the antenna impedance is 75 , determine: (a) total power in FM signal and (b) FM modulation index.
What is the adt output for a temperature of 81 degrees : A HCS12 ATD is set to 10-bit unsigned mode. The voltage references are set to ground and 1.0V What is the ADT output for a temperature of 81 degrees The temperature sensor measures 0 to 100 degrees with an output of 10 mV/degree.
Determine the 60-hz resistance of the line in ohms : A 60-Hz, 765-KV three-phase overhead transmission line has four ACSR 900 kcmil 54/3 conductors per phase. Determine the 60-Hz resistance of this line in ohms per kilometer per phase at 50 degrees Celsius.
Compute the molar solubility : The Ksp of AgCrO4 is 1.9 x 10^-12. Calculate the molar solubility (in mol/L) of Ag2CrO4 in 0.1 M AgNO3.
How the temperature switch turns on the white pilot light : PLC 2 In a motor control system, one master stop pushbutton (Stop) is available for stopping the operation at any time. If the temperature switch (TSW) is closed, pressing the red pushbutton (RedPB) will turn on both motors M1 and M2.
Explain what is the maximum concentration of ba2 : What is the maximum concentration of Ba2+ that can be added to a solution containing 1.5 X 10^-2M of F- without precipitating BasF2? Ksp = 1.7 x 10^-6

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determining how to use the function

Determining how to use the function fft to find the DFT coefficients X[k] of x[n] in Matlab. Also, how would you plot the magnitude of X[k] in Matlab?

  Determine the image frequency and the local oscillator

1-for an FM reciever tuned to 94.5 MHZ using high side-injection and a first IF of 10.7 MHZ, Determine the image frequency and the local oscillator

  Find if circuit overdamped-underdamped or critically damped

A 200 resistor, a 10 mH inductor and a 4.7 µF capacitor are connected in a series circuit. a. Is the circuit overdamped, underdamped, or critically damped b. Write the characteristic equation and find the poles of this circuit.

  What is rms voltage of source in a single loop series

3) What is the RMS voltage of the source in a single loop series circuit if Irms = 1A-30° and Ztotal = 100 65° 4) What is the power dissipated by an electric heater with a resistance of 20? drawing a current waveform of i(t) = 10 sin(60t) Amps

  Find the parameters of the z-parameter two-port

The following measurement were made on a two-port resistive circuit. With port 1 open, V2 =15V, V1 = 10 V, and I2 = 30 A. With port 1 short-circuited, V2 = 10 V, I2 =4 A, and I1 = -5 A. Find the parameters of the z-parameter two-port.

  Etermine the equivalent abcd parameters for the line

a positive-sequence shunt admittance y= j4.4* 10-6 S/km. for this line if it has 70% shunt reactive (inductors) compensation and 40% series capacitive compensation. Half of this compensation is installed at each end of the line.

  What rf bandwidth is required to send the data using qpsk

What RF bandwidth is required to send the data using QPSK? If the RRC filters in the transmitter and receiver are replaced with ones that have ? = 0.20, what are the new RF bandwidths in parts (a) and (b)?

  Write down only the first three harmonics

Four frequencies are applied at the input of a non-linear amplifier. Write down all of the frequency components at the output of the non-linear device. Write down only the first three harmonics. Frequencies of 1205Khz, 1200Khz, 1195Khz

  What are the different methods used in frequency response

what are the different methods used in frequency response analysis

  Plot the swing curve for the machine

Calculate the critical clearing angle and plot the swing curve for the machine - What is the power angle at the end of the 10 cycles?

  Power also noise calculations using decibel conversions

A radio receiver has a noise power N = kTB watts, with T = 100 K and B = 1.0 MHz. The value of k is 1.38 x 10^-23 J/K. What is the noise power in dBW?

  Find the net heat transfer for the process for n

100 kg of a certain gas is contained within a piston-cylinder assembly. the gas undergoes a processwhich the pressure volume relationship is (PV)^n = constant. The initial pressure is 6 bars, the initial volume is 0.2 cubic meters

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd