What is the acceleration of the center of disk

Assignment Help Mechanical Engineering
Reference no: EM13217954

A solid homogeneous cylindrical disk is released from rest at the top of an incline.

Its radius is 0.15 m, its mass 5 kg, the incline angle 30 degrees. The static and kinetic coefficients of friction are 0.15 and 0.1 respectively.

1. What is the acceleration of the center of disk?
2. What is the magnitude of the friction force between the ramp and the cylindrical disk?

 

Reference no: EM13217954

Questions Cloud

Explain at least one biblical principle : Which Statement(s) on Standards for Tax Services apply in this situation (explain how and why they apply)? Cite the specific verse(s) for at least one Biblical principle that you feel is relevant to the situation (explain how and why it applies).
Find the the acceleration of each mass : Two equal masses are connected on either side of a pulley. One of the masses rests on an inclined plane with angle of inclination of b. The other one hangs in mid air.
Target population faces : Two credible sources from the University Library or the Internet that discuss the problems this target population faces and incorporate your findings into your paper.
Determine the magnitude of the load p : Knowing that the modulus of elasticity of brass is 105 GPa, determine the magnitude of the load P for which the deflection of the plug is 1,25 mm downward.
What is the acceleration of the center of disk : What is the magnitude of the friction force between the ramp and the cylindrical disk?
Elements of ethical climate : Recall that mission, explicit policy, and implicit policy are the elements of ethical climate. Which element do you think plays the greatest role in influencing employee behavior?
What is the skidding time : The mass of one wheel is 125 kg and its radius of gyration is 0.75 m. The radius of a wheel is 1 m.
Explain discretion to grant unpaid leave to employees : Mary Tiano, a devout Roman Catholic, worked for Dillard Department Stores, Inc., in Phoenix, Arizona. Dillard's considered Tiano a productive employee because her sales exceeded $200,000 a year. At the time, the store gave its managers the discret..
Motivations for committing violent crime : How do the motivations for committing property crime differ from the motivations for committing violent crime?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the average square distance

Calculate the average square distance between the particles and plot its ratio to the time step . This is the diffusion/dispersion coefficient.

  A pitching wedge a golfer is using gives the ball a initial

A pitching wedge a golfer is using gives the ball a initial angle of 50 degrees, what range of velocities (Vo) will cause the ball to land within 3 ft of the hole?

  Find out the largest couple that can be applied

Determining the largest couple that can be applied to a beam in pure bending. A beam of cross section shown is extruded from an aluminum alloy for which σy = 310 MPa and σu = 480 MPa.

  What is the concentration of fecl3 in a solution

What is the concentration of FeCl3 in a solution prepared by dissolving 20.0 g of FeCl3 in enough water to make 275 mL of solution?

  What is the rotating speed of the disk in rpm

A slotted disk and opto-interrupter outputs pulses at 62 HZ. The disk has only one slot cut in it. what is the rotating speed of the disk in rpm?

  Determine the maximum speed

Determine the maximum speed at which the car with mass can pass over the top point A of the vertical curved road and still maintain contact with the road.

  Review journal paper about types of trucks gap and skirts

Need a critical review journal paper about the different types of trucks gap and skirts and boat tails

  What is the airspeed of the plane

The airspeed of an aeroplane is measured with a Pitot tube. The plane is flying at an altitude of 10000m, and the Pitot tube measures a gauge pressure of p = 10kPa. What is the airspeed of the plane?

  Determine metal removal rate

Determine metal removal rate, etching time, and required dimensions of the opening in the cut and peel maskant required to achieve the desired pocket size on the part.

  Neglect the size of the limb

, determine the speed of the boy at the instant = 4 . Neglect the size of the limb. When = 0, = 8 so that and are coincident, i. e., the rope is 16 long.

  Irrigation system

Irrigation system

  Draw the stress distributions in section aa

A 12 kN force is exerted on a rocker arm. The moment of inertia (I) of the crosssection with respect to the neutral-axis is 43.3x10-9 m4.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd