Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
The output voltage of a power supply is normally distributed with mean 5 V and standard deviation 0.02V. If the lower and upper specification for voltage are 4.95V and 5.05 V, respectively what is the probability that a power supply selected at random will conform to the specification on voltage ?
Given R = 50Kohm and C = 100nF what is the frequency of oscillation Given a required frequency of oscillation of f = 10kHz and R = 8kohm, what should the value of C be
An abrupt p-n junction has a doping concentration of 1015, 1016, or 1017 cm-3 on the lightly doped n-side and of 1019 cm-3 on the heavily doped p-side. Obtain series of curves of 1/C2 versus V, where V ranges from -4 to 0V in steps of 0.5V.
Is it possible to interface an IC with a different technology such as TTL to HCS12 ports What are the conditions in terms of electrical parameters that need to be satisfied for this purpose
Draw a state diagram for an FSM (Moore machine) with no inputs and three outputs x, y, and z, where xyz should always exhibit the following sequence: 000, 001, 010, 100, repeat. Make 000 as the initial state.
The potential energy of a system of two particles separated by a distance r is given by the equation below, where A is a positive constant. U(r) = (A)/(r^11) Find the radial force vector F that each particle exerts on the other.
(a) If five different types of chips are to be placed on the board, how many different layouts are possible (b) If the five chips that are placed on the board are of the same type, how many different layouts are possible
The measurement of a current is repeated five times. The measured values are: 0.62, 6.21. 6.23, 6.18 and 6.24 mA. a. What type or types of errors might be involved: mistakes, systematic errors, random errors
The current entering the positive terminal of a device is 5e-4t A and the voltage across the device is 2 di/dt V. Find the charge delivered to the device between t = 0 and t = 2 s.
An n+p junction with a long p-region has the following properties: Na=10^16 cm-3, Dp=13 cm2s-1, µn=1,000 cm2V-1s-1, tn=2×10-6 s. If we apply 0.7 V forward bias on the junction at 300 K, what is the electric field in the p-region FAR FROM the junct..
For a particular IC-fabrication process, the transconductance parameter k'n = 50 µA/V2, and Vt = 1 V. In an application in which vGS = vDS =Vsupply = 7 V, a drain current of 0.8 mA is required of a device of minimum length of 2 µm.
A voltage source with voltage Vs = V0 sin(pi*t) is driving a load of RL = 100 Ohms. The load is connected to the source by a transmission line with characteristic impedance Z0 = 50 Ohms. The velocity of propagation on the line is 2 108 m/s.
A 10 H inductor is connected in series with a 1.0k(ohm) resistor and a switch which closes at t=0s, Determine the voltage across the inductor and the current through the inductor for t>0 if the inductor has an initial current of 10 A.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd