What is poisson ratio and shear modulus of this material

Assignment Help Mechanical Engineering
Reference no: EM13701084

A 1 foot long cylindrical rod with a diameter of 0.25 inch is subjected to a tensile load of 1,500 lbs. Suppose the rod was elongated 0.01 inch under this load, what is the stress and strain created by the load? What is the Young’s Modulus of the material? If the diameter of the rod is reduced to 0.2478 inch under this load, what is the Poisson ratio and Shear Modulus of this material?

Reference no: EM13701084

Questions Cloud

What is the exit air speed : Air enters a machine at 373 C with a speed of 200 m/s and leaves it at 293 C. If the flow is adiabatic, and the work output by machine is 105 Nm /kg, what is the exit air speed? What is the exit air speed when machine is delivering no work?
The pressure drop per unit length through the crack : A dam with water on one side has a 0.01 inch crack 10 feet below the surface of water. The length of the crack is 5 ft, and the thickness of the dam at that location is 3 ft. The water temperature is 50 degrees F. determine the following: The pressur..
An ideal single reheat cycle uses a turbine inlet conditions : An ideal single reheat cycle uses a turbine inlet conditions of 2500 psia and 1000F and a reheat temperature of 1000F with a reheat pressure ration of P2/P1 = 0.2 and a steam mass flow rate of Ms = 2*10^6 lbm/hr. The condenser operates at a pressure ..
A simple ideal ranking cycle has a power output : A simple ideal ranking cycle has a power output of 660 MW, a turbine inlet condition of T1=1000F, P1=1800 psia and a condenser operating pressure of P2=1.5 psia.
What is poisson ratio and shear modulus of this material : A 1 foot long cylindrical rod with a diameter of 0.25 inch is subjected to a tensile load of 1,500 lbs. Suppose the rod was elongated 0.01 inch under this load, what is the stress and strain created by the load? What is the Young’s Modulus of the mat..
What is the specific volume of the gas before the turbine : Air expands in an air turbine from a pressure of 50 psia and a temperature of 600°F to an exhaust pressure of 20 psia. Assume the process is reversible and adiabatic with negligible changes in kinetic and potential energy.
What is the specific heat capacity of this material : When a total amount of 125,000 joules of heat is transferred to a piece of 5 kg alloy, its temperature changes from 25 C to 60C, what is the specific heat capacity of this material?
A piston-cylinder setup filled with air : A piston-cylinder setup filled with air, initially at 27 °C, 1 bar, changes to 17 °C, and 0.9 bar. Determine, as a present, the change in volume of the air from its initial volume. (in %)
Calculate the energy transfer for each of the components : An air standard dual cycle operates with a compression ratio of 15. At the beginning of the compression the conditions are 17°C, 0.95 bar, and 3.8L. The amount of heat added is 6.3 kJ, of which one-third is added at constant volume and the remainder ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd