What is maximun combined power that can be delivered to load

Assignment Help Electrical Engineering
Reference no: EM13263272

A three phase transformer is constructed from three 3kVA transformer. Secondaries are wired in Delta configuration with a balanced load.

What is the maximun combined power that can be delivered to the load?

Reference no: EM13263272

Questions Cloud

What is the return on invested capital : What is the Return on invested capital (ROIC) for the current year?
What amount of shipping department costs : During the period, the Far East sales office generated 684 orders for a total of 6,120 items. These orders were shipped in 1,474 boxes. What amount of shipping department costs should be allocated to these sales?
What will be the peak current through the switch at instant : A permanent magnet DC motor with a 10 ohms armature is stopped by dynamic braking. at operating speed, the counter EMF in the motor armature is 15 volts. What will be the peak current through the switch at the instant it shorts out the motor
Determine the allowable shaft load in horsepower : A three-phase, 125-hp, 60Hz, eight-pole, 575-V, design B induction motor is to be operated from a 50-Hz system. Determine (a) allowable voltage at 50 Hz; (b) allowable shaft load in horsepower; (c) new synchronous speed
What is maximun combined power that can be delivered to load : A three phase transformer is constructed from three 3kVA transformer. Secondaries are wired in Delta configuration with a balanced load. What is the maximun combined power that can be delivered to the load
Determine the ionization energies of the shells : The K series of the discrete x-ray spectrum of tungsten contains wavelengths of 0.018 5 nm, 0.020 9 nm, Determine the ionization energies of the L, M, and N shells
What is a budget and what are good budgeting practices : Why is it important to monitor the cash flow of an organization? What can happen if this activity is not well established?
Determine the recoil speed of the hydrogen atom : Assuming that the atom was initially at rest, determine the recoil speed of the hydrogen atom when it emits this photon
What would be the diffusion rate in a channel : The diffusion rate for a solute is 4.0 × 10-11 kg/s in a solvent-filled channel that has a cross-sectional area of 0.50 cm2, What would be the diffusion rate m/t in a channel with a cross-sectional area of 0.30 cm2

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Determine the 4th discrete fourier transform

the frequency response h(e^jw) of a length-4 finite impulse response filter with a real impulse response h[n] that the following specific value: h(e^j0)=13, H(e^j3pi/2)=-3-j4, and h(e^jpi)=-3. determine the 4th discrete fourier transform (DFT) of ..

  Calculate the resistance of the coil of copper wire

A coil made of 150 turns of copper wire wounded ona cylindrical coil . If that means radius of the turns in 6.5mm and the diameter of the wire is 0.4mm, calculate the resistance of the coil.

  Which would have a higher line reactance in ohms

1. which would have a higher line reactance in ohms. An overhead 138KV line or an overhead 34KV line. Why. 2. Does line charging amps increase or decrease with line length. Why

  Determine phase lag for the system if the input u given

Consider the stable system represented by the differential equation: dx(t)/dt + 3x(t) = u(t) Determine the phase lag for this system if the input u(t) = sin3t.

  Design a new p-type semiconductor material

design a new p-type semiconductor material. Acceptor density is Na=5x1015 cm^-3 and there are no donors are present in the material. The effective densities of states for this material is given as Nv=1.8x10^19cm^-3

  What are the requirements for the circuit supplying

In terms of good desgn practice , what is the number of receptacles allowed on a general purpose 15 A 120V circuit. A 20A and 120V circuit. What are the requirements for the circuit supplying bathroom in residences

  Find the steady state temperature distribution of the tray

The tray heats up according to ut = c2?u + h(x, y) where h(x, y) = 5(1 - sin(8πy)) and c2 = 10-4. Assume that u = 200 along each edge. Find the steady state temperature distribution of the tray.

  Compare the input and output impedance for transistor

As far as a direct compaison of mechanical switches vs. transistors used as switches, the transistor does have a measurable impedance when ON, and a mechanical switch does not.

  Calculate the gross and net power generated by the generator

A tractor-trailer truck driver friend often delivers to companies that do not have a fork truck or loading dock. She wants to install a lift-gate on her trailer so she can load and unload her truck without a fork truck.

  Determine the impulse response for the system

noncausal, linear, and time-invariant. Determine the impulse response for the system and verify that an LTI system defined by the impulse response you determined satisfies the difference equation.

  Write an integral expression that gives g as a function of f

Consider two continuous signals f(x, y) and g(x, y) that are separable, show that their convolution is also separable. Show that the 2-D Fourier transform of the rect function is the sinc function.

  Find what is the output power of the final amplifier stage

Three amplifiers with power gains of 15, 22, and 7 are cascaded. The input power is 120 µW. What is the output power of the final amplifier stage

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd