What is level 0 protective clothing and ppe

Assignment Help Mechanical Engineering

Reference no: EM131309113

Health and Safety Management

1. The following gas detector tubes are available for direct reading of concentrations of the toxic gas hydrogen sulfide

Tube	Concentration
4HT	1-40%
4HH	0.1-4.0%
4H	10-3200 ppm
4M	12.5-500 ppm
4L	1-240 ppm
4LL	0.25-60 ppm

Which of these tubes would be satisfactory for detecting OSHA specified ceiling concentration for hydrogen sulfide? Of the satisfactory tubes, which ne tests the narrowest range of concentrations?

2. A process engineer proposes a new solvent that will reduce the quantities required by the process and significantly reduce the quantities of solvent vapors released into the air inside the pant. The new solvent is perchloroethylene, and it is expected to reduce the solvent vapors absorbed into the plant by 20% by volume as compared to old solvent? (Stoddard solvent. You are called in as a Certified Safety Professional to evaluate the proposed change to the process. Do you support the process change? Explain your position
For these two questions, you can refer to the Appendix A of the book.

3. A glue making process releases ethylene glycol that becomes generally diluted and intersped through the plant atmosphere. The rate of release is 2.4 cubic feet per hour vapor volume at standard temperature and pressure. The plant dilution system is of general dilution type with makeup air being suppled through windows and doors throughout the plant area? The plant area is 12,000 square feet and the average ceiling height is 16 feet. The problem is to specify the capacity of the general ventilation system required to maintain a steady-state condition throughout this process area that protects against both health and safety hazards due to ethylene glycol. For your information in performing calculations, the following data is provided.

Ethylene glycol

· Molecular weight : 62.1

· Boiling point 197.5 °C

· LEL: 3.2%

· Firepoint -13 °C

· Flashpoint: 232 °F

· Autoignition temperature: 752 °F

· Vapor pressure: 0.05 mm at 20 °C

· PEL: 50 ppm (ceiling)

a. How much exhaust ventilation (in cubic feet per hour, general diulution tpe) is required to maintain safety hazards below explosive levels?

b. How much exhaust ventilation (in cubic feet per hour, general dilution type) is required to maintain health hazards below OSHA-specified action levels?

c. How many plant area room changes would be the level of ventilation calculated in part (b) present?

4. A worker exposure to noise in a given plant is measured, resulting in the following readings for various time periods during 8-hour shift?

8:00 A.M.-9.00 AM 86 dBA

9:00 A.M.-11 A.M. 84 dBA

11 a.m.-12 noon 81 dBA

12 noon-1:00 P.M. 101 dBA

1:00 P.M-4:00 P.M. 75 Dba

a. Perform computations to determine whether maximum PELs have been exceeded based on TWA calculations.

b. Have the ALs have been exceeded?

c. Given the noise exposure just described, would the employer be required to furnish hearing protectors?

d. Would employees be required to use the hearing protectors?

e. Suppose the engineering control could be devised that could cut the noise level (sound pressure level) in half either in the morning or in the afternoon, but not both. Which would you select? Why?

5. A full revolution press with two engagement points on the flywheel has two hand palm buttons installed at a distance of 16 inches from the point of operation. Calculate the minimum flywheel speed that will permit this press in compliance with standards. Explain why

a slower flywheel would be more dangerous.

6. A hospital administrator wants an estimate of X-ray idle time that has a 95.5 percent confidence of being within 4 percent of the actual percentage. Previous analysis indicates that on the average X-ray machine is busy 25% of the time. What sample size should be used?

7. Please provide answers on the following questions written outside of lectric panel.

a. What is Level 0 Protective clothing and PPE?

b. What is shock hazard?

c. What is arc flash hazard?

d. What is arc flash boundary?

e. What is 208 VAC?

f. What is NFPA-70E?

g. What is HRC level?

h. What type of general safety precautions you need to take while working around electric panels?

Reference no: EM131309113

Questions Cloud

Demonstrate relationship of theory to practice problem : Operationalization of theory paper - Highlights key components of the theory. Includes and explains a diagram of theory modified to demonstrate relationship of theory to practice problem

What is the per capita income of residents of greenville : What is the per capita income of residents of Greenville?- What is the name and address of the president of TCBY?

How much did celestial actually invest this year : Now suppose that at the end of the year, Celestial had produced 950,000 units but had only sold 900,000 units and that inventories now contained 50,000 units more than they had at the beginning of the year. At $100 each, that means that the firm a..

Analyze the parent goal of the maintain node : Analyze the parent goal of the Maintain [SufficientRouteSeparation] node. Determine the incompleteness in the provided model fragment and fix the anomaly. Explain what the anomaly is and propose a way for it to be rectified.

What is level 0 protective clothing and ppe : How much exhaust ventilation is required to maintain safety hazards below explosive levels?How much exhaust ventilation is required to maintain health hazards below OSHA-specified action levels?How many plant area room changes would be the level of..

Evaluate the quality of internet resources : Search for news about a company that interests you. Use the questions for "Evaluating Web Resources," and submit a brief summary of your analysis.

How might capacity be measured : How might capacity be measured? In what ways is capacity limited by labor constraints and by capital constraints? What are the consequences if demand in the economy exceeds capacity? What signs would you look for?

Write this query without using a join operator : Write a query that retrieves student.last_name, student.first_name and total number of enrollments from the student and enrollment tables. Write this query without using a join operator.

What do the cpi and the ppi measure : What do the CPI and the PPI measure? Why do we need both of these price indexes? (Think about what purpose you would use each one for.)

User Account

All Pages