What is his quarterly payment

Assignment Help Mechanical Engineering
Reference no: EM13711768

Bill borrowed $10,000 to be repaid in quarterly instalments over the next 5 years. The interest rate he is being charged is 10.26% per year compounded quarterly. What is his quarterly payment? Give answer without $ sign with 2 decimal place precision.

Reference no: EM13711768

Questions Cloud

A direct part of the federal government : Select any two (2) of the following questions. As you develop your essay, remember to include not only text materials but also contemporary materials as well. These can come from various sources and can reflect domestic and/or global concerns.1..
Determine the time required by a diesel-electric locomotive : Determine the time required by a diesel-electric locomotive, which produces a constant drawbar pull of 60,000 lb, to increase the speed of an 1800 ton freight train from 20 mi/hr to 30 mi/hr up to 1-percent grade. Train resistance is 10 lb per ton.
Use simulink to do the simulations of the step responses : Write down the transfer function of a third-order system with unity steady-state gain which has a real pole at s = -1 and a pair of complex poles at s = -1 +- ja. Simulate the open-loop step response of the system for 'a' values of 1, 2, 4, and 10, a..
A correct statement regarding transactions : 1. According to double-entry accounting, which of the following is a correct statement regarding transactions? Each transaction must increase an asset and a liability. Purchasing supplies on account is shown by an increase on the left side of the T-..
What is his quarterly payment : Bill borrowed $10,000 to be repaid in quarterly instalments over the next 5 years. The interest rate he is being charged is 10.26% per year compounded quarterly. What is his quarterly payment? Give answer without $ sign with 2 decimal place precision..
What is the velocity in ms through the orifice : A 3cm inside diameter pipe has a 1 cm orifice installed in it. The pipe is flowing 150g/s water. What is the velocity in m/s through the orifice? What is the Reynolds number? The orifice Coefficient, Cv? What is the pressure drop in Pa?
What is the entropy change of the flame : You are boiling a kettle of water over a propane stove that is supplying a uniforma amount of heat. You note that it takes 3 minutes to heat water which is initially at 20C to its boiling point. Just as the water begins to boil, you receive a phone c..
Determine the force required to hold the nozzle : Water (at 15 C) flows out of a nozzle that is attached to a garden hose. The volume flow rate is through this nozzle at a rate of 25 x 10-5 m3/s, which discharges into the atmosphere. The diameter of the garden hose is 1.5 cm, while the diameter of t..
Assume a fire truck can shoot water from an onboard tank : Assume a fire truck can shoot water from an onboard tank; there is no inflow of water into the tank. What force must a truck engine produce to keep the truck stationary while the fire hose shoots a jet at 45 degrees at a volume flow rate of 2.4 m3/s ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the actual power transmitted to the second pulley

Calculate the actual power transmitted to the second pulley and calculate the power which can be transmitted if the maximum tension in the belt is limited to half of the ultimate strength of the belt.

  Species concentration in chemical reactor

A fourth-order polynomial passes through the five points for which the independent and dependent variables, x and y, respectfully, are given (-2,37), (-1,7), (0,5),(1,13), and (2,61). Find the polynomial by any suitable method. Here, x represents the..

  Define and design a hollow steel shaft to transmit

Hollow shaft transmitting power with shear limits. Design a hollow steel shaft to transmit 300 hp at 75 rpm without exceeding a shear tress of 8000 psi. Use 1.2:1 as the ratio of the outside diameter to the inside diameter.

  After the block is released from rest it travels upward and

a block of mass 0.256 kg is placed on top of a light vertical spring of force constant 4 925 nm and pushed downward so

  Determine the maximum height h achieved the total flight

an experimental fireworks shell is launched vertically from point a with an initial velocity of magnitude v0 80 ftsec.

  Standard machining parameter formulae for milling

Using the standard machining parameter formulae for milling, determine the speed (rpm), feed (ipm) and machining time (TM) recommended to horizontal mill ANSI #1018 cold rolled steel that is 1.50 inch long with a 10 tooth 4.0 inch diameter slab mill ..

  What equal amount can you withdraw from the account at the

today you have a savings account of 15 620. based on an annual interest rate of 4.2 what equal amount can you withdraw

  A hot-water stream at 80 degrees c enters a mixing chamber

a hot-water stream at 80 degrees c enters a mixing chamber with a mass flow rate of 0.5 kgs where it is mixed with a

  Suppose we load this cart with a crate of mass 104 kg where

you are given a four-wheeled cart of mass 15 kg where the distance between a wheel and its nearest neighbors is 2 m.

  A 250-kg crate b is suspended from a cable attached to a

a 250-kg crate b is suspended from a cable attached to a 20-kg trolley a which rides on an inclined i-beam as shown.

  A 100 kva 3- phase star- connected transformer has a

a 100 kva 3- phase star- connected transformer has a primary voltage of 11000 v and a secondary voltage of 440 v and it

  A material has a strength coefficients

A material has a strength coefficients K = 100, 000 psi Assuming that a tensile-test specimen made from this material begins to neck at a true strain of 0.17, show that the ultimate tensile strength of this material is 62,400 psi.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd