Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
A DSP engineer applies DFT to 500 data samples that are sampled at 250 Hz to plot the signal spectrum. What is the frequency that corresponds to the frequency bin number ?
A 2 farad capacitor is charged up to 400v by a dc power supply. How long in seconds would it take to discharge the capacitor to a safe stored energy level of 1 joule using a 1k ohm high wattage resistor bank.
Design a 300W PFC BL-Zeta converter operating in DCM (Output Inductor) to maintain a DC link voltage of 100V with percentage ripple of 4%. The permitted ripple in the input side inductor and intermediate capacitor is given as 20%.
An abrupt p-n junction has a doping concentration of 1015, 1016, or 1017 cm-3 on the lightly doped n-side and of 1019 cm-3 on the heavily doped p-side. Obtain series of curves of 1/C2 versus V, where V ranges from -4 to 0V in steps of 0.5V.
Single Phase Circuit, A resistor and a capacitor are connected in series across a 150 V a.c supply. When the frequency is 40 Hz the current is 5 A
A buck converter has input voltage of 10 V, switching frequency 1 kHz, The load resistance of 5 Ω requires average voltage of 5 V with a maximum ripple of 20 mV. The maximum ripple current of the inductor is 0.2 A.
Assume that the I bit for external hardware interrupt IRQ is enabled and is low-level triggered. Explain how this interrupt works when it is activated. How can we make sure that a single interrupt is not interpreted as multiple interrupts
Design an 8-bit register with 2 control inputs s1 and s0, 8 data inputs I7..I0, and 8 data outputs Q7..Q0. s1s0=00 means maintain the present value, s1s0=01 means load, and s1s0=10 means clear. s1s0=11 means to swap
A linear-phase FIR filter should be designed with the ideal magnitude response shown in Figure 1 which represents an narrow band-pass filter. The lower cutoff frequency, fL , is 2,000 Hz, and higher cutoff frequency, fH , is 3,600 Hz.
discharge a capacitor of 1mF charged with a voltage of 1 volt we connect it, at time t = 0, with a esistor of R ohm. When we measure the voltage we find it to be V(r) (t) = e ^(-t) u(t). Determine the resistance of R. If the capacitor has a capaci..
Design a combinational logic circuit which has one output Z and a 4-bit input ABCD representing a binary number. Z should be 1 iff the input is at least 5, but is no greater than 11. Use one OR gate (three inputs) and three AND gates
An FM transmitter delivers to a 75 ohm antenna a signal voltage of V (t)= 1000 sin (10^9t+4 sin 10^4t), determine: (a) carrier frequency; (b) intelligence frequency; (c)modulation index; and (d)total power in FM signal
The maximum voltage that James can apply to this capacitor is limited by Vmax = Kd, where K is the breakdown strengh of the dielectric. deriven an expression for the maximum energy that can be stored in this capacitor in terms of K and the volume ..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd