What is coefficient of restitution needed for good ammo

Assignment Help Mechanical Engineering
Reference no: EM13711600

A "pumpkin chucker" designed for the annual pumpkin competition held near Millsboro, delaware every fall (first week of November) uses a pneumatic launcher (air cannon) to throw its pumpkin. It is important to know if your "ammunition", the pumpkin, can withstand the force exerted on it during launch) otherwise it comes onto a solid wood board placed on the deck of their truck. The problem is that if the pumpkin bounces 1ft off the board after dropping from 5ft up, without obvious damage, the pumpkin is resilient enough to be used as ammo. What is the coefficient of restitution needed for good ammo?

Reference no: EM13711600

Questions Cloud

Types of consequences of operant conditioning : Man's Best Friend: The Biology and Behavior of Dogs Describe a response that can be classified as classical conditioning (such as vet trips, grooming, thunder phobia, etc.) Describe four types of consequences of operant conditioning?
In air-conditioning systems-streams of cold and warm air : In air-conditioning systems, streams of cold and warm air are mixed to get air with the right temperature. Consider a mixing chamber into which cold air enters at 8C and 100 kPa at a rate of 0.55 m^3 /s and warm air enters at 300C and 100 kPa. The ra..
Range of projectile and velocity on impact given inputs : (MATLAB) given a cannon ball that is shot upwards at an angle, the time taken for the cannon ball to hit the ground is: Write a single function that outputs the total time of flight, range of projectile and velocity on impact given inputs. Use the fu..
A woman is admitted to the emergency room : A woman is admitted to the emergency room because the tissues in her legs are retaining water. She is diagnosed with severe pitting edema-any pressure applied to the swollen tissue leaves a temporary indentation or "pit" in the tissue, even wh..
What is coefficient of restitution needed for good ammo : A "pumpkin chucker" designed for the annual pumpkin competition held near Millsboro, delaware every fall (first week of November) uses a pneumatic launcher (air cannon) to throw its pumpkin. It is important to know if your "ammunition", the pumpkin, ..
Difference between causes and effects in the swot analysis : Difference between causes and effects in the SWOT analysis.Causes are important, not effects. Once the SWOT Analysis is created, each group needs to construct the SWOT Bivariate Strategy Matrix.
Shell-and-tube heat exchanger is used to cool flow of steam : A shell-and-tube heat exchanger is used to cool a flow of steam using a stream of cooling water. The steam enters the heat exchanger at 0.1 bar and a quality of 91% (state 1), and exits as a saturated liquid at the same pressure (state 2). The mass f..
Briefly explain how gmos are created : Briefly explain how GMOs are created in your own words.
Fire truck draws water from an open constant-level reservoir : A fire truck draws water from an open constant-level reservoir through a hose of 0.2 ft2 cross section. The water is discharged from the pump through another 0.2 ft2 hose to a surge tank pressurized to 120 psig with air at the top. The pump adds 970 ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd