What happens when the transistor changes to a pnp transistor

Assignment Help Electrical Engineering

Reference no: EM131296747

Lab Assignment

Transistor Fundamentals

Introduction:

Lab is based on the fundamentals of a transistor and analysis of an analog circuit.

Please review the following videos before getting started with this lab:

1. Watch the video: "Video 3: Fundamentals of breadboard"-
https://content.grantham.edu/at/EE212/1-20-2015/week2/Fundamental_of_Breadboard.mp4

2. Watch the video: "Video 4: Basic electrical components"
https://content.grantham.edu/at/EE212/1-20-2015/week2/Basic_Electrical_Components.mp4

3. Watch the video: "Video 5: Simple resistive circuit with NI myDAQ"
https://content.grantham.edu/at/EE212/1-20-2015/week2/Simple_Resistive_Circuit_with_NI_myDAQ.mp4

Materials and Equipment:

Materials:

• Hardware Parts (In the Toolbox):

o An NPN transistor: 2N3904
o Two resistors: 10 kΩ and 3.6 kΩ
o Jumper wires

Equipment:

• Hardware Equipment:

o Breadboard
o NI myDAQ Instrument device
o Screw Driver
o Screw Terminal connector
o USB Cable
o Multimeter probes
o Oscilloscope, Multimeter and Function generator from NI ELVISmxIntrument Launcher

Procedure:

This lab has to be implemented only in hardware (using NI myDAQ)

6. Analyze the circuit in the Figure 1 below to calculate the following values: V_E, I_E, V_RC, V_C, V_CE. Make sure to include 20% tolerance for each resistor in the calculations.

7. Construct the circuit shown in Figure 1 below on the breadboard using the transistor and two resistors (R_C and R_E).

8. Using the jumper wires, screw driver and screw terminal connector, connect the board to NI MyDAQ Instrument Device.

9. Use channel +15V pin out on the NI myDAQ Instrument Device to provide the supply voltage (V_CC) and channel AO0 to provide the base voltage (V_BB). Make sure that this voltage is peak-to-peak. Use channel AI0 to measure the required voltages using the oscilloscope.

Figure 1

Using the function generator from NI ELVISmx Instrument Launcher, provide the input voltage V_BB to the circuit.

Use the oscilloscope to measure the voltages: V_E, V_RC, V_C, V_CE.

Now, using multimeter with the probes, measure the required voltages: V_E, V_RC, V_C, V_CE and currents: I_C and I_E.

Tabulate the values obtained in step 1 and 7.

	Calculated	Measured
V_E
I_E
V_RC
V_C
V_CE

Review questions:

9. Compare the calculated and measured values in the table and analyze the performance of the transistor.

10. Discuss whether the values are the same or different. If they are different, provide the reasoning and explain how to reduce this difference between calculated and measured values.

11. Explain what happens when the transistor changes to a PNP transistor. How does the change in the transistor effect the current and voltage in the circuit?

Deliverables:

12. Analysis of the circuit and calculations of voltages: V_E, V_RC, V_C, V_CE and currents: I_Cand I_E.

13. Place your student ID card on the breadboard and take a picture of the circuit board and pin out on the NI myDAQ Instrument Device.

14. Take screenshots of the measurements obtained from function generator and Multimeter on the NI ELVISmx Instrument Launcher on your screen.

Lab Report:

• Use the Lab report template found in the "Tools and Template" link in the navigation center.
• Include all the deliverables.
• Include all the screenshots of the measurements from Multisim, circuit design on the breadboard using NI myDAQ device and measurements from MI ELVISmx Instrument Launcher.
• Save the document as Lab4YourGID.docx (ex: Lab4G00000000.docx) and submit in Blackboard.

Reference no: EM131296747

Questions Cloud

Explain the benefits of reducing inventories : Questions - Explain the benefits of reducing inventories and setup times. Briefly discuss the contributions of Deming, Crosby, and Juran to Quality Management

What are some advantages of the software as a service model : What are some advantages of the software as a service (SaaS) model?- Why has it been successful in the CRM space?

Aggregate demand and supply : Image that the mayor has hired you as a consultant to evaluate the increase in aggregate demand in the city where you live. Describe to the mayor one (1) aggregate demand and supply factor that would have the greatest impact on the economy of your..

Describe roles of the five key stakeholders in a business : Describe the roles of the five key stakeholders in a business? Explain how and why the ownership of a business may spread.?

What happens when the transistor changes to a pnp transistor : Explain what happens when the transistor changes to a PNP transistor. How does the change in the transistor effect the current and voltage in the circuit?

Read the case and answer the below question : MLT 107: Hematology/Phlebotomy-read the case and answer the below question. List the equipment that should be used, and how should the phlebotomist proceed to collect the specimen?What problems could the phlebotomist encounter during this draw?

How nonprofit organization and for profit businesses similar : Discuss the economic, industry, and global environments and explain how they may affect the business environment?

Efficiency of tax system and equity of tax system : Analyze the difference between the efficiency of a tax system and the equity of a tax system as it refers to the costs imposed on taxpayers using the benefits principles.

Explain why people are willing to be entrepreneurs : Explain why people are willing to be entrepreneurs, even though they might potentially lose all the money that they invest in the business?

User Account

All Pages