What diameter is required if the concrete pipe is to carry

Assignment Help Civil Engineering
Reference no: EM13297405

A ciricular sewer is laid on a slope of 0.5%. What diameter is required if the concrete pipe is to carry 25 cfs? If the desired design mean suction velocity is between 3 and 7 ft/s, is the design acceptable?

Reference no: EM13297405

Questions Cloud

What fraction of the beam is reflected and transmitted : A beam of protons, each with kinetic energy of 40MeV, approaches a step potential of 30MeV. What fraction of the beam is reflected and transmitted
Determine what are air flow and particulate concentration : Three streams of polluted air are combined prior to treatment in an electrostatic precipitator (ESP). The flow and particulate concentration of each stream are 600 cfm at150 mg/m^3, 700 cfm at 200 mg/m^3, and 500 cfm at 1000 mg/m^3.
Calculate the earnings after taxes for the firm : Calculate the earnings after taxes for the firm assuming a 40 percent tax on ordinary income. (Please calculate the arithmetic solution and show your work)
What is the angle of reflections : If a beam is incident normal (perpendicular to the surface) to a plane mirror, what is the angle of reflections
What diameter is required if the concrete pipe is to carry : A ciricular sewer is laid on a slope of 0.5%. What diameter is required if the concrete pipe is to carry 25 cfs If the desired design mean suction velocity is between 3 and 7 ft/s, is the design acceptable
What is the mass of the wagon : A child pulls on a wagon handle at an angle 37° above the horizontal with a force of 45 N. what is the mass of the wagon
What is the mean section velocity in the expanded section : Water flows at 8 m^3/s through a rectangular channel 4 m wide and 3 m deep. If the velocity is 1 m/s, calculate the flow depth in the channel. If this channel expands downstream to a width of 5m and the depth decreases by 0.5m from the upstream de..
The real gdp and consumption data for nation b in 1996 is : The real GDP and consumption data for nation b in 1996 is in the following table. The investment is 25 billion, and government purchases is 5 billion, assume nation b has no international trade and tax. Real GDP in billions. 100. 200. 300. 400. 500 6..
Determine the outlet temperature of the engines compressor : The thermal efficiency of an aircraft gas turbine engine (turbojet, based on ideal Brayton cycle) is 25%. The aircraft travels at a speed 770 km/h at an altitude 6800 m above sea level (standard atmospheric air). The combustion chamber outlet temp..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Discuss energy storage scheme from a conversion efficiency

an electrical-generation utility sometimes pump liquid water into an elevated reservoir during periods of low electrical consumption. this water is used to generate electricity during periods when the demand for electricity exceeds the utilities a..

  Draw streaklines for a dye stream that was emitted

A flow has circular streamlines. At t=0 the flow is in the clockwise direction and the angular velocity is pi rad/s. This flow exists for 1 s, and then reverses to counterclockwise with an angular velocity of -pi rad/s for 1 s.

  Long-term average precipitation in the colorado river basin

The long-term average January precipitation in the Colorado River basin is 1.11 inches, with a standard deviation of 0.60 inches. Assuming a normal distribution, what is the probability that less than 0.5 inches of precipitation will occur in any ..

  Compute the maximum acceptable tensile service load

Compute the maximum acceptable tensile service load T that may act on a single angle L6x4x3/4 that is welded along only one leg to a gusset plate; thus, there are no holes. The service load is three times the dead load. Solve for a0 A36 steel.

  What is the total bod loading per day

The factory will use a 4 ft deep on-site lagoon to stabilize the waste with a loading rate of 20 lb BOD/acre-day. Part a) What is the total BOD loading per day?

  Determine the design speed of the curve

an equal-tangent sag vertical curve is designed with the PVC AT STation 109 + 00 and elevation 950 ft, the PVI at station 110 + 77 and elevation 947.34ft,and the low point at station 110 + 50 . Determine the design speed of the curve.

  Determine the difference in the rate of grade

indicate the conditons by a sketchand determine the difference in the rate of grade at the intersection of each of the following paris of slops.

  Maximum tensile and compressive bending stresses

When P = 800 lb, A) Draw the shear and bending moment diagram along its length; B) Determine the maximum tensile and compressive bending stresses; and C) determine the maximum shear stress.

  Thermo-gravimetry of calcium oxalate

Evaluate the percent mass loss for each of the three thermal events indicated on the attached TGA trace

  Calculations with steam mixed with additional steam

Calculations with steam mixed with additional steam at a different pressure, A steam press at 650Kpa + dryness fraction of 0.9% flows along a pipe at a rate of 3.5Kg per second

  Determine the distance the engine is hoisted

The 3.5-Mg engine is suspended from a spreader beam having a negligible mass and is hoisted by a crane which exerts a force of 40 kN on the hoisting cable. Determine the distance the engine is hoisted in 2.4 s, starting from rest.

  Compute minimum footing width required to maintain safety

a bearing wall carries a dead load of 120kn/m and live load of 100 kn/m. It is to be supported on a 400mm deep continuous footing underlain by a medium sand (unit weight = 19.2 kn/m3, phi= 37 deg, effective c = 0).

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd