What concentration of ozone should be injected

Assignment Help Civil Engineering
Reference no: EM13555148

Ozone is sometime used as a disinfectant for drinking water. Ozone is highly reactive it will react benign species found in water, as well as the pathogens it is intended to kill. It found that ozone reaction in water nearly follows first-order kinetics in ozone concentration, such as that its concentration decreases by 50 percent in 12 minutes (t1/2 = 12 min).

A water supplier wants to inject ozone into a piper bringing water to the water treatment plant to predisinfect the influent. The 3.0-ft diameter piper is 3,400 feet long with a steady flow rate of 10,000 gal/min. what concentration of ozone (in mg/L) should be Injected at the head of the piper so what there will be an ozone concentration of 1.0mg/L at the piper’s exit into the plant? The piper may be realistically assumed to act as an ideal PFR.

Reference no: EM13555148

Questions Cloud

What is the percentage error in the bulk unit weight : What is the percentage error in the bulk unit weight if the soil is the percentage error in the bulk unit weight if the soil is 95% saturated but assumed to be 100% saturated?
What must be the allowable elongation : A cylindrical rod of brass alloy (E = 100 GPa,) having a yield strength of 345 MPa is to be subjected to a load of 7500 N. If the length and diameter of the rod are 338 mm and 7.55 mm respectively, what must be the allowable elongation?
What should be the concentration of pollutant : A lagoon with volume 1,200 m3 has been receiving a steady flow of a conservative waste at a rate of 100 m3/day for a long enough time to assume that steady-state conditions apply. The waste entering the lagoon has a concentration of 10 mg/L. assuming..
With what velocity will air enter the room under : Laboratories containing dangerous materials are often kept at a pressure slightly less than ambient pressure so that contaminants can be discharged through an exhaust system rather than leaked through cracks and around doors to other parts of the bui..
What concentration of ozone should be injected : Ozone is sometime used as a disinfectant for drinking water. Ozone is highly reactive it will react benign species found in water, as well as the pathogens it is intended to kill.
Determine the percentage increase in the discharge : As part of a drainage improvement project, a drainage ditch will be straightened and cleaned. As a result, the lenght of the ditch will decrease from 1800 ft to 1400 ft and the mannings roughness factor will be reduced
What will be the porosity of the mixture : You are furnished with three sizes of particles. One is gravel with porosity of 0.32, the second is a coarse grained sand with porosity of 0.37, and the third is a fine grained sand with porosity of 0.23. If the coarse grained sand
Determine redox state of sulfur in both the compounds : Derive the porosity values for cubic, orthorhombic, and rhombohedral packing of spheres. Include sketches supporting your calculations of the bulk volumes of the unit cells.
Calculate the plasticity index the liquidity index : The soil is under a rectangular concrete slab 15m x 50m, used as a foundation for a building. A water pipe, in diameter id located in a trench 450mm below the center of the slab. The trench running along the length of the slab,300mm wide and 450mm de..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Design the appropriate reinforced concrete footing on a soil

A combined footing is subjected to an exterior 16 in. x 16 in. column abutting the property line carrying a total service load Pw = 300,000 lb and an interior column 20 in. x 20 in.

  How many truckloads of trucks hauling an average volume

How many truckloads of trucks hauling an average volume of 6 LCY (4.6 LCM) would be required to haul 1 million CCY (764, 600 CCM) of gravel to a dam site

  Calculate head supplied by the pump for the system

Water from a lower reservoir (water surface elevation) 500 m is pumping to the upper reservoir (water surface elevation 600 m) through a 5000 m long straight pipe with 0.5 m diameter.

  Calculate the velocity of the end of the whip as a function

A whip crack is illustrated below. To crack the whip, it is thrown forward with a velocity of 10 m/s and the handle is stopped in a vertical position instantly forming a tight loop that propagates forward.

  To produce an economic design for a structural

It has been decided to use an approximate grid of 3.75metres by 6.75 metres for an office building, which is to includefacilities for general filing and storage space.

  Find the uniform flow depth of concrete trapezoidal channel

Find the uniform flow depth (in feet) of a concrete trapezoidal channel with a bottom width of 30 ft. and side slopes of 2:1. The channel is laid at a slope of 0.05% and carries a design discharge of 1000 cfs.

  Design a three story office building

Design a three story office building

  Determine the hydraulic conductivity of the soil sample

The sediment sample is 30 cm long. The porous plates on top and bottom of the sample holding it in place have a vertical hydraulic conductivity of 0.001 cm/s and each have a thickness of 10 cm.

  V is the shear force at the same point

Follow the derivation of the following equations for deflections of a beam, filling in all the required assumptions and steps in the derivations.EIv'' = M EIv''' =V EIv'''' = ? q where v is the deflection of the beam, E is Young's modulus

  Calculate the mean fragmentation size using kuz ram

The mine wants to change the hole diameter to 229 mm and needs a new drilling pattern that will not result in coarser fragmentation. For this exercise you can assume homogenous geology and no adverse effects due to geological structure.

  What is the stationing and elevation of the high point on

A vertical curve is designed for 90 km/h and has an initial grade of +2.5% and final grade of -1.0 %. the PVT is at station 3+480. It is known that a point on the curve at station 3+440 is at elevation 75m. What is the stationing and elevation of the..

  Explain how to determine the power input to the pump

Water enters the pump of a steam power plant as saturated liquid at 20 kPa at a rate of 45 kg/s and exits at 6 MPa. Neglecting the changes in kinetic and potential energies and assuming the process to be reversible

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd