What clamping force will remain when this value of p acts

Assignment Help Mechanical Engineering
Reference no: EM131377875

Two aluminum plates, which are part of an aircraft structure, are held together by a grade 7½, UNF bolt. The effective area of the aluminum plates in compression is estimated to be 12 times the cross-sectional area of the steel bolt. The bolt is initially tightened to 90% of its proof strength. Gust loads, varying from zero to P, tend to pull the plates apart (this results in negligible bolt bending). With a safety factor of 1.3, what is the maximum value of P that will not cause eventual bolt fatigue failure? What clamping force will remain when this value of P acts?

Reference no: EM131377875

Questions Cloud

Discuss about the case given below : This is a summary of events that provides context to the issues discussed in the appeal. This most often includes a summary of events which lead to an arrest and trial of the defendant. It should also include some of the arguments made by the part..
Explain whether the company will prevail : The company thereafter discontinued payments, alleging that no contract had been made by the board of directors, because Feinberg had paid no consideration, and that the resolution was merely a promise to make a gift. Explain whether the company w..
Discuss the validity and effect : Johnson and Wilson were the principal shareholders in XYZ Corporation, located in the city of Jonesville, Wisconsin.- Discuss the validity and effect, if any, of this agreement.
What is the fundamental frequency of the ecg signal : ECET345- What is the fundamental frequency of the ECG signal? Why are there so many components in the spectrum of the ECG signal compared to the sine wave signal?
What clamping force will remain when this value of p acts : what is the maximum value of P that will not cause eventual bolt fatigue failure? What clamping force will remain when this value of P acts?
Discuss whether wilkins would be successful : Discuss whether Wilkins would be successful in an action against Coverton seeking to recover a fee in the amount of $1,500 as the reasonable value of his services.
Discuss about the post given below : For several years, "The MacDonald Triad", named after the forensic psychiatric, JM MacDonald, was used as a predictive tool when examining the common traits of serial killers. The three traits primarily found in these suspects were:Cruelty to anim..
Will christy prevail in given case : Subsequently, on Michael's refusal to pay Christy, Christy sues Michael for damages for breach of contract. Will Christy prevail? Explain.
Estimate the bolt-tightening torque required : What is the safety factor (factor by which the 18-kN load could be multiplied) for fatigue? Assume an idealized stress-strain curve based on Sy.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd