What are their compositions and amounts

Assignment Help Mechanical Engineering
Reference no: EM13719312

Assume that the overall composition is 0.6 wt%C (and 99.4 wt%Fe) and a total weight of 10Kg. At T=727C, how many phases are present and what are their compositions and amounts?

Hint: For the very last part of this problem, first calculate the amounts "just above" and "just below" the given temperature separately, and then explain your conclusion for T=727C. You may also want to revisit lever rule and its derivation for obtaining the amount at T=727C

Reference no: EM13719312

Questions Cloud

Water initially exists as a saturated liquid : Water initially exists as a saturated liquid at 186oC is contained in a piston-cylinder assembly. The water undergoes a process to the corresponding saturated vapor state, during which the piston moves freely in the cylinder
Assume variable specific heats : Air contained in a rigid, insulated tank fitted with a paddle wheel, initially at 4 bar, 40oC and volume of 0.2 m^3, is stirred until its temperature is 500 K. Assuming the ideal gas model for the air, determine the amount of entropy produced, in kJ/..
Determine the exit temperature of the air : Air enters the evaporator section of an air-conditioner at 100 kPa, 27oC with a volumetric flow rate of 6 m^3/min. R-134a enters the evaporator at 120 kPa with a quality of 0.3 and rate of 2kg/min and it leaves as a saturated vapor at the same pressu..
Heat transfer is negligible are kinetic and potential energy : Steam at 550 lbf/in.2, 70 oF enters a turbine operating at steady state and exits at 1 lbf/in.^2. The turbine produces 500 hp. For the turbine, heat transfer is negligible as are kinetic and potential energy effects.
What are their compositions and amounts : Assume that the overall composition is 0.6 wt%C (and 99.4 wt%Fe) and a total weight of 10Kg. At T=727C, how many phases are present and what are their compositions and amounts?
Find the steady state temperature in the plate : You have a 2 dimensional (just X&Y) square plate with sides measuring a=24. The upper and lower sides of the plate are perfectly insulated, but the right and left sides are not. The left side is kept at 0°C and the right side is kept at f(y) °C. Find..
Find the temperature in the middle of the bar : You have a bar of silver of length 10 cm and constant cross section of area (density 10.6 g/cm^3), thermal conductivity , specific heat that is perfectly insulated laterally, with the ends of the bar kept at 100*C for a long time. Then at some instan..
Identify and describe existing and potential competitors : Identify and describe existing and potential competitors/allies, then summarise the strengths and weaknesses of each - Develop a separate summary statement
What is a database transaction : What is a database transaction? List and define the transaction properties. It is important that you answer in your own words. Please use diagrams to enhance your answer.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Pitot-tube equation to determine the actual wind speed

A meteorologist uses a pitot -static tube to measure the wind speed in a tornado. Based on the damage caused by the storm, the tornado is rated as EF5 on the enhanced Fujita Scale. This means that the wind speed is estimated to be in the range of 261..

  A 500in wide x 25in thick flat steel plate steps down to a

a 5.00in wide x .25in thick flat steel plate steps down to a width of 2.50in and is subjected to axial force. there is

  Compute the modulus of elasticity of the metal

During a test of a metal bar, it was found that a axial tensile force of 10,000 lbs resulted in an elongation of 0.023 in. The bar had these original dimensions, length 10 in. diameter 0.750 in. Compute the modulus of elasticity of the metal. What ki..

  What is the amount of shaft work produced by a typical ic

a gallon of liquid gasoline contains about 131 mj 124340 btu of energy. this fuel is atomized and burned with the

  One kilogram of air as an ideal gas executes a carnot power

one kilogram of air as an ideal gas executes a carnot power cycle having a thermal efficiency 50. the heat transfer to

  What is an exergy factor 8 what is a pinch point and what

what is an exergy factor? 8 what is a pinch point and what is it used for? 9 what does the compressor in figure 2 do?

  An electric field is e400nci for xgt0 and e-400nci for xlt0

an electric field is e400nci for xgt0 and e-400nci for xlt0. a cylinder of length 30cm and radius 10cm has its center

  What is the initial temperature and initial internal energy

suppose 2 kg of water at 300 kpa has a specific volume of 0 5m3kg. as a result of heating at constant pressure the

  Estimate the maximum efficiency of conversion of thermal

it has been proposed that energy be taken as heat from the atmosphere around milwaukee and used to run a power plant.

  Determine the change in pressure required to reduce

If the bulk modulus for water at 70 degrees Fahrenheit is 319 kips per square inch, determine the change in pressure required to reduce its volume by 0.3%

  Calculate the limestone feed rate lbhr assume that the flow

a power plant produces a flue gas with a mass flow rate of 2 million pounds per hour. of that 150000 lbhr is water

  If only one extraction from the turbine occurs at 10 bar

a regenerative steam cycle operates between the limits of 80 bar 540oc and 0.05 bar. if only one extraction from the

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd