What are the wall temperatures at that location and at the

Assignment Help Mechanical Engineering
Reference no: EM13644731

Air at a velocity of 35. 2 ft / see and a pressure of 793. 1 nun Hg flows in a long circular pipe whose inside diameter is 0. 78 in. At the inlet, the temperature of the air is 70. 3 F. Heat is transferred from the pipe wall to the air along an axial length between the inlet and a downstream location that is 10. 3 feet from the inlet. Downstream of that location, the pipe wall is perfectly insulated. The air temperature is measured at the exit of the insulated section as 129. 7 F. Required results: What is the rate of heat transfer Q to the air between the inlet and the 10. 3 ft location? If the heating were uniformly distributed, what is die heat flux q? Suppose that fully developed conditions are achieved at a downstream distance from the inlet of 3 ft. What are the wall temperatures at that location and at the 10. 3 ft location? Calculate the arithmetic-mean temperature difference and the log-mean temperature difference for the heated section.

Reference no: EM13644731

Questions Cloud

When she leaves the track she follows the characteristic : the drawing shows a skateboarder moving at v 5 ms along a horizontal section of a track that is slanted upward by
If the reaction of moco6 with mesitylene was conducted in : if the reaction of moco6 with mesitylene was conducted in the presence of air what would likely be the decomposition
She calculates a power of 043 for that increased from a : a marketing analyst at an internet book store is testing a new web design which hopes to increase sales. she wants to
The nonconservative wind and lift forces take the balloon : a 6.00 x 102 kg hot-air balloon takes off from rest at the surface of the earth. the nonconservative wind and lift
What are the wall temperatures at that location and at the : air at a velocity of 35. 2 ft see and a pressure of 793. 1 nun hg flows in a long circular pipe whose inside diameter
As a system increases in volume it absorbs 525 j of energy : as a system increases in volume it absorbs 52.5 j of energy in the form of heat from the surroundings. the piston is
A sol of unknown calcium concentration is titrated using : a sol. of unknown calcium concentration is titrated using edta. the edta is first standardized against a primary
After flying for 15 min in a wind blowing 42 kmh at an : after flying for 15 min in a wind blowing 42 kmh at an angle of 28deg south of east an airplane pilot is over a town
1 for a population that is normally distributed with a mean : 1. for a population that is normally distributed with a mean of 100 and standard deviation of 10 what value would

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd