What are the wall temperatures at that location and at the

Assignment Help Mechanical Engineering
Reference no: EM13644184

Air at a velocity of 35. 2 ft / sec and a pressure of 793. 1 nun Hg flows in a long circular pipe whose inside diameter is 0. 78 in. At the inlet, the temperature of the air is 70. 3 F. Heat is transferred from the pipe wall to the air along an axial length between the inlet and a downstream location that is 10. 3 feet from the inlet. Downstream of that location, the pipe wall is perfectly insulated. The air temperature is measured at the exit of the insulated section as 129. 7 F. Required results: What is the rate of heat transfer Q to the air between the inlet and the 10. 3 ft location? If the heating were uniformly distributed, what is die heat flux q? Suppose that fully developed conditions are achieved at a downstream distance from the inlet of 3 ft. What are the wall temperatures at that location and at the 10. 3 ft location? Calculate the arithmetic-mean temperature difference and the log-mean temperature difference for the heated section.

Reference no: EM13644184

Questions Cloud

How does the excess co2 gas in the atmosphere cause the : 1. what is the greenhouse effect?2. how does the excess co2 gas in the atmosphere cause the greenhouse effect?3. what
When using the normal approximation to the binomial what is : when using the normal approximation to the binomial what is the standard deviation for a binomial probability
A 3 ft3 adiabatic rigid container is divided into two equal : a 3 ft3 adiabatic rigid container is divided into two equal volumes by a thin membrane. initially one of these chambers
Use a psychrometric chart to determine the following : a sling hygrometer measures a dry-bulb temperature of 24. 5 degree c and a wet-bulb temperature of 16 degree c. use a
What are the wall temperatures at that location and at the : air at a velocity of 35. 2 ft sec and a pressure of 793. 1 nun hg flows in a long circular pipe whose inside diameter
A solution containing 1513 g of glucose in 1000g of water : a solution containing 15.13 g of glucose in 100.0g of water was found to freeze at -1.29c with a 1.53 cm. what is the
A 14- container of liquid nitrogen is kept in a closet : a 1.4- container of liquid nitrogen is kept in a closet measuring 1.2 by 1.2 by 1.9 . assuming that the container is
The action of an alkaline i2 solution on the rodenticide : the action of an alkaline i2 solution on the rodenticide warfarin c19h16o4 308.34 gmol results in the formation of 1
A 06407 g sample containing chloride and iodide ions gave a : a 0.6407 g sample containing chloride and iodide ions gave a silver halide precipitate weighing 0.4430 g. this

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd