What are the possible water levels in the tank at the end of

Assignment Help Civil Engineering
Reference no: EM13540143

A cylindrical tank is used to store water for a town. on any given day, the water supply inflow per day may fill the tank with additional 6, 7, or 8ft of water. the daily demand or consumption of the water for the town will draw down the water level in the tank by an amount equivalent to 5, 6, or 7ft of the water in the tank. what are the possible combinations of inflow and outflow of water in the tank in a given day? if the water level in the tank is 7ft from the bottom at the start of day, what are the possible water levels in the tank at the end of the day?

Reference no: EM13540143

Questions Cloud

How many hours should it take an articulated wheel loader : How many hours should it take an articulated wheel loader equipped with a 4 yd bucket to load 3000 cu yd of gravel from a stockpike into rail cars
What will be the discharge : A concrete sewer pipe 1m in diameter is laid so it has a drop in elevation of 30cm per 300m of length. If sewage (assume the properties are the same as those of water) flows at a depth of 50cm in the pipe, what will be the discharge?
What power output may be expected from the turbine : If the discharge is 500cfs, what power output may be expected from the turbine? Assume that the turbine efficiency is 90% and that the overall head loss is 1.5V 2/2g, where V is the velocity in the 7 ft penstock. Assume a=1.0 at all locations.
The ratio of volumetric strain to diametral strain is : A w24x192 of a242 steel is to be used as a beam. what are the values of yield stress Fy ultimate tensile stees Fu and modulus of elasticity E for this beam?
What are the possible water levels in the tank at the end of : A cylindrical tank is used to store water for a town. on any given day, the water supply inflow per day may fill the tank with additional 6, 7, or 8ft of water
Find the stress in the cable when the truck comes : A tow truck is using a cable to pull a car up a 15 degree hill. If the car weighs 4000 lbs and the cable has a diameter of .75 inches, find the stress in the cable when the truck comes to a stop while on the hill. Ignore friction between the car and ..
Will the pesticides threaten the fish population during the : In the summer, the density at the top of the lake is 997 kg/m3, and at the bottom is 1000 kg/m3. Would you predict stratification to be present, and if so assume an epilimnion depth of 4m. Will the pesticides threaten the fish population during the s..
How fast will the sleeve slide down the rod : A sleeve 30 cm long encases a vertical rod 2.5 cm in diameter with uniform radial clearance of 0.005 cm. when the sleeve and the rod are immersed in a pool of oil with dynamic viscosity
Select the required commercial size of the rod required to : Two forces are applied as shown to hook support. Knowing that the magnitude of P is 35 N, determine by trigonometry (a) the required angle a if the resultant R of the two forces applied to the support is to be horizontal, (b) the corresponding magnit..

Reviews

Write a Review

Civil Engineering Questions & Answers

  Solve the problem using the darcy weisbach

An effluent holding pond to be used as part of a spray irrigations system is being built.  The holding pond is located 2.5 miles awary for the 10 mgd WWTP which will supply the effluent

  What percentage of the hexane entering the condenser

A gas stream contains 18.0 mole% hexane and the remainder nitrogen. The stream flows to a condenser, where its temperature is reduced and some of the hexane is liquefied. The hexane mole fraction in the gas stream leaving the condenser is 0.0500.

  Discuss types of earth moving used in field of engineering

Find the swell for a soil which weighs 1600kg/m in bank and 1300kg/m3 in bank and 1300kg/m3 Loose and what is the shrinkage factor for a mass of soil that takes up 1.5m3 in bank and reduces down to 1.2m3 after compaction

  Estimate the moisture content and moist density

A 0.4m^3 moist soil sample has the following: Moist mass = 711.2 kg, Dry mass 623.9 kg, Specific gravity of soil solids = 2.68 Estimate: a). Moisture content. b). Moist density.

  What are the volumetric flow rates of the two outlet streams

A permeation membrane separates an inlet air stream (79 mol% N2, 21 mol% O2) into a permeate stream and a reject stream. The inlet stream conditions are 293K, 0.5 MPa and 2 mol/min; the conditions for both outlet streams are 293 K and 0.1 MPa.

  Determine the support reactions in a steel i beam

A steel I beam is supported by a pin at point A and a rocker at B, and a cable applies a 2000lb force. The beam is uniform and weighs 26 lb/ft. Determine the support reactions.

  What is the absolute pressure at the surface of the mercury

The container is vented to the local atmosphere. What is the absolute pressure at the surface of the mercury and at the bottom of the container. Assume the conditions of the standards atmosphere prevail for pressure. Use sg = 13.54 for the mercury..

  Determine by trigonometry the required angle of forces

two forces applied as shown to a hook support. knowing that the magnitude of P is 35 N, determine by trigonometry the required angle if the resultant R of the two forces applied to the support is to be horizontal and the corresponding magnitude of..

  Calculate the overall efficiency of the system

A gas stream with a particulate loading of 20.0g/m^3 is passed through a 70%-efficient cyclone followed by a 95%-efficient ESP. Calculate the overall efficiency of the system.

  Determine the seepage velocity-v through the sample

The cross-sectional area of the sample was 60 cm2 and its length was 150 mm. For 80 cm3/min steady-state flow rate, a total head difference of 8 cm was measured across two points separated by 10 cm along the axis of the sample.

  Calculate the dry unit weight of the compacted earth fill

During construction of a highway project, a soil sample was taken from compacted earth for a sand-cone in place denstiy test. The following data were obtained from the test. Weight of sand used to fill test hole and funnel of sand-cone device= 845..

  Determine how many units of each product company should make

The number of hours on each machine required to produce a product is given in the following table, along with the number of hours available per week on each type of machine. Assume that the company can sell everything it produces.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd