What are the minimum value of the magnitude ratio and the

Assignment Help Mechanical Engineering
Reference no: EM13631512

A pressure transducer has a natural frequency of 50 kHz and a damping ratio of 0.4. It is to be used to measure pressures with frequencies of up to 10 kHz. A digital data acquisition system is to be used.

a. What is the minimum sampling rate to be specified?

b. Since noise is broadband, i.e., it may exist at frequencies higher than 10 kHz, determine the minimum cutoff frequency for an anti-aliasing filter.

c. What are the minimum value of the magnitude ratio and the maximum value of the phase shift of the transducer output when measuring signals at frequencies of equal or less than 10 kHz?

Reference no: EM13631512

Questions Cloud

Solid particles having a size of 018 mm a sphericity shape : solid particles having a size of 0.18 mm a sphericity shape factor of 0.91 and a density of 1090 kgm3 are to be
A hundred volt potential difference is suddenly applied to : the deflection plates in an oscilloscope are 10cm by 2cm with a gap distance of 1mm. a hundred volt potential
A book was published entitled one million random digits in : a book was published entitled one million random digits. in it there are listed one million 1000000 digits each of
Determine the minimum possible work for the process include : a tank of volume 12m3 is initially filled with air at 22deg and 100 kpa a vacuum pump slowly removes air from the tank
What are the minimum value of the magnitude ratio and the : a pressure transducer has a natural frequency of 50 khz and a damping ratio of 0.4. it is to be used to measure
Explain why the total flux nevertheless is proportional : 1. explain why you are safe and unaffected inside a car that is struck by lightning. also explain why it might not be
In a study of pregnant women and their ability to correctly : in a study of pregnant women and their ability to correctly predict the sex of their baby 56 of the pregnant women had
It has been shown that the cop for a carnot refrigerator is : it has been shown that the cop for a carnot refrigerator. is greater than the cop for a real refrigerator . show the
There is about a 50-50 chance that the percentage of : in a certain city there are 3000000 registered voters of whom 1200000 are democrats. a survey organization is about to

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A pitot-static tube is used to measure the velocity of 20

a pitot-static tube is used to measure the velocity of 20 degrees c 68f water flowing in an open channel. if a

  Find its magnitude for impending motion

A body having a mass of 46 kg rests on a horizontal planse for which the coefficiant of friction f = 0.4. A force P acts ofn the body at an angle of 20 degrees with the horizontal. Find its magnitude for impending motion.

  Calculate the isentropic efficiency of the turbine if the

an adiabatic turbine handles air as the operating fluid such that the air is expanded from 2 mpa and 327 degc to 200

  The case for global accounting standards arguments and

the case for global accounting standards arguments and evidencethis paper outlines the arguments for a basic set of

  Which has the larger area moment of inertia a 2 x 2 square

1. which has the larger area moment of inertia a 2 x 2 square beam of high strength stainless steel or a 2 x 2 square

  What is the rate at which radiation is emitted by surface

2.51 a body whose surface area is 0.5 m2 emissivity is 0.8 and temperature is 150 is placed in a large evacuated

  If the final pressure is 1 bar determine the specific

the inlet condition for a turbine is saturated vapor r134a at 20 bar pressure. if the final pressure is 1 bar determine

  Compute the stress level

For this same component and alloy, compute the stress level at which fracture will occur for a critical internal crack length of 6.0mm.

  What is the aerodynamic drag force acting on the car

you are driving your car with a manual transmission down a 6 grade and notice that when your foot is off the throttle

  The diameter at the point of fracture is 101 1 mm 0398 in

a cylindrical aluminum specimen having an original diameter of 12.8 mm 0.505 in. and gauge length of 50.80 mm 2.000 in.

  Crate slides down the section of the spiral ramp such that

crate slides down the section of the spiral ramp such that r .5zft and z 100 - .1t2ft where t is in seconds. if the

  What is the reason for the change in enthalpy

what is the reason for the change in enthalpy between the throttle valve and the evaporator in a practical refrigeration cycle that is using R12 refrigerant.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd