What are the impedance and the component value of the load

Assignment Help Electrical Engineering
Reference no: EM13280139

A balanced, three-phase, Y-connected source has a line voltage of 440 Vrms. The source frequency is 60 Hz. The balanced, three-phase loads have the following characteristics:
Zy1: P1 = 15 kW and Q1 = +18 kVAR
Z?2: |S2|=21 kVA and PF2 = 0.500 lagging
Z?3: PF3 = 0.2 lagging and Ip3 = 25 A rms
Zy4: 1.67?60º O
(note, power values are all three-phase quantities)

1. Determine each impedance and the current for each load.
2. Determine the total line current, IaA.
3. Determine the total complex power, average power, and reactive power delivered by the source to the loads.
4. What is the power factor of the four loads combined?
5. It is necessary to add a parallel load in the configuration to the circuit to minimize the magnitude of the line current. The line voltage and total average power delivered by the source may not change. What are the impedance and the component value of this load?
6. What is the power factor of the additional load?
7. What is the power factor of the five loads combined?

Reference no: EM13280139

Questions Cloud

Explain naturally occuring sulfur consists of four isotopes : Naturally occuring sulfur consists of four isotopes: 95.0% 32s (31.97207amu); 33s (32.97146amu, 0.76%);
Calculate the market return : I am using the CAPM to determine the expected return on Mcdonalds. But in the formular, a market return is need. Then how can I calculate the market return?
How fast must he motorcycle leave the cliff : A motorist speeds horizontally of a 50.0 meter high cliff. If the motorist wants to land on level ground below 90.0 m form the base of the cliff. how fast must he motorcycle leave the cliff top to make this landing
Explain what is the percent yield of hcl : if 20. g or NaCl are used and only 5.6 g of HCl are isolated, what is the percent yield of HCl C.) If only 5.6 g of HCl are obtained, how many grams of Na2SO4 must also have been formed
What are the impedance and the component value of the load : A balanced, three-phase, Y-connected source has a line voltage of 440 Vrms. The source frequency is 60 Hz. The balanced, three-phase loads have the following characteristics: Zy1: P1 = 15 kW and Q1 = +18 kVAR Z?2: |S2|=21 kVA and PF2 = 0.500 laggin..
A subcellular organelles separated by ultracentrifugation : If a eukaryotic cell were broken open and the subcellular organelles separated by ultracentrifugation, in which of the following would the citric acid cycles be found
Sketch two periods of the output signals out1 and out2 : Channel 1 and channel 2 are configured to generate output signals OUT1 and OUT2, with TACCR1 = 745, and TACCR2 = 499, respectively. And the output mode is set to Reset/Set. Sketch two periods of the output signals OUT1 and OUT2 (with proper labeli..
What does the profitability index measure : What does the profitability index measure? How would you state the profitability index rule?
What is the dollar value of the tax shield on that debt : Legitron corporation has $350 million of debt outstanding at an interest rate of 9 percent. What is the dollar value of the tax shield on that debt, just for this year, if Legitron is subject to a 35 percent marginal tax rate?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find the line to neutral voltage phasors of the power

Each phase of the load consists of an impedance of 30 + j40 ohms. Find the line to neutral voltage phasors, the line to line voltage phasors , the power and the reactive power delivered to the load. Assume that the phase of Van is zero.

  Implementation of ga matlab code

Project on LFC using tuned FOPID. I have considered a two area model. Need help regarding implementation of GA MATLAB code for a two area interconnected power system for LOAD FREQUENCY CONTROL.

  Find the current that flows in a silicon bar of 10-µm length

Find the current that flows in a silicon bar of 10-µm length having a 5-µm x 4-µm cross section and having free electron and hole densities of 105 / cm³ and 1015 / cm³, respectively, when a 1 V is applied end-to-end. Use µn = 1200 cm²/V·s and µp =..

  How big will be rated power of motor for starting current

How big will be rated power of the motor if starting current at star-connection and phase to phase voltage of the supply 380 V is (150+17) A. the ratio of starting current for motor is 7 Ir efficiency factor is 0.85 but cos f =0.8

  Sketch sop realization using nands and pos using nors

Design a circuit that has 4 inputs, WXYZ, and two outputs, f and g, where W is the most and Z is the least significant bit. The output f is asserted whenever the two-bit number WX is greater than the two-bit number YZ.

  Determine what is the switching voltage

Suppose that two optical guides embedded in a substrate such as LiNbO3 are coupled as in the below figure and the transmission length Lo=10mm. If the coupling separation d is =10µm, n = 2.2, the operating wavelength is 1.3µm

  Estimate the time required for the diode to turn off

A silicon diode with a breakdown voltage of 2000V that is conducting a forward current of 2000A is turned off with a constant diR/dt=250 A/s. Roughly estimate the time required for the diode to turn off.

  How to draw a linear graph including the 5 steps over 10ms

DC supply=18v Motor Noload speed=9,000RPM 018V ton=40% -60% in 10ms in 5 steps a) Calculate B for each of the 5 steps b) calculate Vavrage over 10ms c)calculate no load speed d)draw a linear graph including the 5 steps over 10ms

  Calculate the electric current moving through

A glass tube with a cross-sectional area of 9^-2 m^2 contains an ionizd gas. The densities are 10^15 positive ions/m^ and 10^11 free electrons/m^3. Under the influence of an applied voltage, the postive ions are moving.

  What current is needed in the coil to produce flux of 200 wb

A closed solenoid has a 100 turn coil. That core has a reluctance of 0.8(A-T/Wb). What current is needed in the coil to produce a flux of 200 Wb

  What is the torque on the loop from the magnetic field

A coil of wire contains 50 square turns, each one 5 cm long and 3 cm wide, and has a current of 30 A running through it. it is placed inside a magnetic field of 0.55 T at a 60 degree angle. what is the torque on the loop from the magnetic field

  Determine what is total number of voice calls per operator

Each of these bands is split into two, allowing two operators. An operator is allocated 12.5 MHz in each direction. Each channel is allocated 30 kHz. If 21 channels are allocated for control, what is the total number of voice calls per operator.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd