What are the horizontal distances

Assignment Help Civil Engineering
Reference no: EM13533436

1.In a venturi meter the gage pressure is 120 kPa whencavitation just starts to occur. If the Diameter is 40 cm and theneck diameter is 14 cm, what is the water discharge in the systemfor this condition of incipient cavitation?

Atmospheric pressure is 100 kPa gage, and water temperature is10 degrees C.

2.The slope distances shown were measured with an EDM while the differences in elevation between the ends of each line were determined by leveling. What are the horizontal distances?

Slope Distance(ft)                         

a. 1310.81

b. 792.22

c. 656.72

Elevation Difference

a. -36.96

b. -17.03

c. 13.44

3.A motorcycle is 125 kg and a center of mass at G1, while the rider is 75 kg and has a center of mass G2. If the coefficient ofstatic friction between the wheels and the pavement is Us=.8;determine if it is possible for the rider to do a "wheely", i.e.,lift the front wheel off the ground. What acceleration is necessaryto do this? Neglect the mass of the wheels and ssume that the front wheel is free to roll. all necessary distances are given.

Reference no: EM13533436

Questions Cloud

Calculate the diameter of this pipe : Using the Hazen-Williams approach (seecoefficient table below), find the headloss of water flowingthrough 1,000-ft of 6-ft diameter concrete pipe at a flow rate (Q)of 80 ft3/sec
What is the oil flowrate in stb : Two wells had been drilled on 40-acre spacing. Well 1 is injectionand Well 2 is producing well. Downhole injection pressure is 8500psi, and bottomhole pressure in producing well is 2400 psi.
How many passengers per day are carried : A bus line 4 miles long runs through an area with 1/6 acre lots,3.5 people per household, average 1 car per household. People willwalk up to 1/6 mile to a bus stop, so stops are located 1/3 mileapart along the route. Say commuters will tolerate 20 mi..
What is the demand for time if left turns are provided : Given the following geometry of an intersection: Four lanes fornorth and southbound traffic; two lanes for east and west boundtraffic. The peak hour volume for
What are the horizontal distances : The slope distances shown were measured with an EDM while the differences in elevation between the ends of each line were determined by leveling. What are the horizontal distances?
Which of these is correct surely not both : Adequately describe the abiotic factors that determinethe types and numbers of species found in yourzone. Examples of factors: temperature, access to sunlightfor photosynthesis, dissolved oxygen content, availability of nutrients such as carbon.
To produce an economic design for a structural : It has been decided to use an approximate grid of 3.75metres by 6.75 metres for an office building, which is to includefacilities for general filing and storage space.
How would the graph the bending moment : How would I graph the bending moment? There is a uniformly distributed load throughout the whole beam and a 3kN force at 1.5m from A (start of the beam)and 3m from A.
Why would we use prestressed concrete to build : How we can find the applicaition of internal force in civil? mean an appication for the internal force in the civil

Reviews

Write a Review

Civil Engineering Questions & Answers

  Compute the maximum likelihood estimate of the probability

The article "Statistical Evidence of Discrimination" (Journal of the American Statistical Association, 1982, pp.773-783) reported that, prior to 1965 in a southern state, 25% of those eligible to serve on a grand jury were black

  Find the piles axial capacity if k is assumed to be 7

A 12-in. square concrete pile is driven into loose sand to a depth of 30 feet. Unit weight is 118 pcf, internal friction is 30 degrees. Find the pile's axial capacity if K is assumed to be 0.7 and the factor of safety is 2.

  How fast will the car be traveling when it reaches the tree

a car is traveling at sea level at 78 mi/h on a 4% upgrade before the driver sees a fallen tree in the roadway 150 feet away. the coefficient of road adhesion is 0.8. The car weighs 2700 lbs, has a drag coefficiant of 0.35, a frontal area of 18 ft..

  Determine largest angle through which end a can be rotated

Knowing that the modulus of rigidity is 77 GPa for the steel and 27 GPa for the aluminum, determine the largest angle through which end A can be rotated if the following allowable stresses are not be exceeded

  Determine the amount of garbage produced in the city

A city with 28,000 percent population is planning solid waste program. Population growth in the city is estimated to be 2.2% annually and the planning will designed for 30 years, The dumping area is located 20km away from the city.

  Determine the speed of the falling rain in ft per second

An interesting application of the relative motion equations is the experimental determination of the speed at which rain falls. Say you perform an experiment in your car in which you park your car in the rain and measure the angle the falling rain..

  Determine the magnitude of the projected components of f

(a) Determine the magnitude of the projected components of F acting parallel Fp and normal Fn to line OA. (b) Express these components Fp and Fn in Cartesian vector notation.

  Calculate for the whole catchment values of annual average

A watershed has four sub-areas. The annual precipitation and evaporation from each of the sub-areas are given in Table(below). Assume that there is no change in groundwater storage on an annual basis and calculate for the whole catchment the value..

  What will temperature rise of lead be if there is no cooling

Consider the steady-flow energy equation applied to the given extrusion process. Since the die is horizontal then there will be no change in potential energy from inlet to outlet. Hence the potential energy terms can be neglected.

  Determine the force exerted on the tank bottom

A cylindrical water tank is suspended vertically by its sides. The tank has a 10-ft diameter and is filled with 20 degree celcius water to a 3-ft depth. Determine the force exerted on the tank bottom

  Determine the final temperature of the steam

The force on the piston is such that it maintains a constant pressure of 400 kPa inside. A valve is now opened nad steam at 1 MPa, 200 degrees C is allowed to enter the cylinder until the volume inside increases to 0.04 m^3.

  Write possible goal-scope and functional unit for the lca

You are preparing a life-cycle assessment of different transportation options for getting from your house to work (10 miles each way). The options include carpooling with three or more people, one person in a car, bicycling, or taking the bus.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd