Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1.Two 25-kip loads are maintained 6 ft apart as they are moved slowly across the 18-ft beam ab. write a computer program and use it to calculate the bending moment under each load and at the midpoint c of the beam for values of x from 0 to 24 ft at interval delta x = 1.5ft
2.What are the basic assumptions of the 'traffic flow model' and 'capacity model' used in signal timing design? Discuss.
3.A masonry project requires 900 sf repointing. Labor of this activity is given as in the CREW, 1 brick mason and 1 helper. The productivity is 0.5 labor hours per 1 sf. The wages are for the mason $60 and for the helper $45 per hour. The cost of labor in dollars will be:
a) 100
b) 110
c) 115
d) 105
Assuming that the shear stress in the bolts is uniform, determine the number of bolts necessary to make the maximum shear stress in the shaft equal to the shear stress in the bolts. Each bolt has a diameter d.
The cable that supports the bar has an effective modulus and area of 14GPa and 77mm^2 , respectively. Let the lengths be 600mm and 300mm , and the angle 50 degrees . If the permitted additional elongation of the cable is 0.20mm
Two objext A and B are moving along the same line. At the time t=0, B is 75ft ahead of A. The acceleration of A is 1.8ft/s^2 and the acceleration of B is -1.3ft/s^2. The velocity of A is 32ft/s and the velocity of B is 51ft/s.
Provide a reasonable design for a 99% efficient ESP treating 7500 m^3/min of gas. The particles have an effective drift velocity of 10.0 cm/s.
A froth flotation process is used to concentrate copper ore. It is a two stage process with a rougher stage followed by a cleaner stage. The cleaner tailings are returned to the rougher flotation.
A plate 6 inch wide and 1/2 inch thick is lapped over and welded to a gusset plate. determine the minimum length of a 5/16 inch, side fillet weld that will be necessary if the plate is subjected to an axial stress of 20 ksi
Sub 12 means from stage one to two. Heat transfer (Qsub12) occurs to a fluid of mass m whose volume increases at a constant pressure of 21 bar. Assume that the fluid is air (Csubv=0.718 kJ/kg *K and R=0.287 kJ/kg*K) and that Tsub1=725K and Tsub2=1100..
calculate the numbers of married men, single men, married women and single women. Print these numbers on a student summary report. If any single men are over 30 years of age, print their names and ages on a separate eligible bachelors report.
Repeat LEM(Limit Equilibrium Method) analysis in clay (undrained) using a circular failure surface, with the center of the circle a distance h above the edge of the footing. What ratio of h/B gives the minimum value of Nc
Suppose a utility generates electricity with a 36 percent efficient coal-fired power plant emitting the legal limit of 0.6 lb of SO2 per million Btus of heat into the plant. Suppose the utility encourages its customers to replace their 75-W incandesc..
You have two wires connected end to end. Wire 1 is copper and wire 2 is made using a special carbon conductor. Wire 1 has a resistance of 0.215 ohms/ft and is 500 ft long. Wire 2 has a resistance of 0.141 ohms/ft and is 700 ft long.
A steel rod of 1/8 inch diameter is bent into a loop 10 feet in diameter. Determine the maximum flexural stress in the rod.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd