What amount of tension do you need to apply not to have any

Assignment Help Civil Engineering
Reference no: EM13541216

A 100 ft tape was standardized and the length was 100.000 ft whensupported throughout at the room that has a temperature of 68oF andwas pulled with a tension of 10 lb. The weight and cross sectionalarea of the tape were 1 kg, and 0.05 cm2, respectively. The modulusof elasticity is 2.1 x 106 kg/cm2.

You are using that tape to measure the distance between two pointswhere the tapes are supported at the ends only. The temperature ofthe day is 68oF. What amount of tension do you need to apply not tohave any corrections in the tape measurement?

Reference no: EM13541216

Questions Cloud

Total amount of capital available for investments : Formulate the problem mathematically and formulate and solve the above problem on a spreadsheet using Excel - total amount of capital available for these investments
Formulate a mixed-integer optimization model : Formulate a mixed integer programming model for the given problem by defining your decision variables, and writing your objective functions and constraints - formulate a mixed integer linear programming model for the problem
Calculate the discharge if the downstream water height : Water discharges from an irrigation pond (water surfaceelevation 230 ft) through a 4 ft diameter circular orifice. Theinvert elevation of the orifice is at 213 ft and the bottom of the pond has an elevation of 205 ft. Assuming a Cd = 0.60, calculatet..
What is the annual equivalent value of ageometrically : Assume he has to reach a town 300km away, and that the 40 kg he carries includes both merchandiseand the food necessary for his sustenance during the trip at 2000Cal/day.
What amount of tension do you need to apply not to have any : You are using that tape to measure the distance between two pointswhere the tapes are supported at the ends only. The temperature ofthe day is 68oF. What amount of tension do you need to apply not tohave any corrections in the tape measurement?
Estimate the annual number of additional cancers per year : Why don't we assume that there is an unknown moment about B? It the solution it only shows a horizontal force at B. And is there a reason why the horizontal force at B is labeled By?
Determine the dry density of the soil : A small hole about 4" in diameter and 6" deep is dug into acompacted layer of a soil embankment. 2.96 lbs of motor oil withGs=0.92 is required to fill the hole.
What is the terminal velocity of mass m : A 73-mm diameter aluminum (SG=2.64) piston of 100-mm length residesin a stationary 75-mm inner diameter steel tube lined with SAE10W-30 oil at 25C. A mass m=2kg is suspended from the free end ofthe piston
When will the loan be paid off : A person applied a mortgage of $300,000.A mortgage company claimed the interest rate for the 15-year loanis 6.5%. (a) What would be the monthly payment? (b) If the personaccepted the terms of the loan on Oct.

Reviews

Write a Review

Civil Engineering Questions & Answers

  What total allowable bod kg per day could be discharged

A 5000 m3/day wastewater treatment plant discharges to a river with a minimum drought flow of 140 m3/min (upstream of outfall) a)What total allowable BOD (kg/day) could be discharged by the plant if the BOD in the river after initial dilution must ..

  What is the maximum pressure on the form in psf

What is the maximum pressure on the form in PSF?

  Calculate pressure and piezometric head at free surface

Calculate the pressure, and the piezometric head at the free surface, at both interfaces, and at the tank bottom. Take the elevation datum at the bottom of the tank.

  Determine what is the liquid limit of the soil

In a liquid limit test, the moisture contents correspond to 20, 25 and 35 blows are 36% and 20%, 15% respectively. What is the liquid limit of the soil

  How does a heavy truck parked on a prestressed bridge girder

According to the design philosophy in the AASHTO Specifications, how does a heavy truck parked on a prestressed bridge girder effect the nominal shear resistance of the girder

  What is the work done by the air in the cylinder

A piston cylinder is initially at a state of 60c, 200kpa. Heat is added to the system from 500c reservoir until the final pressure is 400kpa. the mass of the air is 2kg, the spring constant is 1000kn/m and the cross sectional area of the piston is..

  What is shear force exerted by oil on m long section of pipe

the flow profile is such that u=u(max)*(1-(r/R)^2) where u is the flow speed and r is the distance from the centre of the pipe in the radial direction. What is the shear stress on the pipe wall What is the shear force exerted by the oil on a 1m lo..

  Compute and compare the hydraulic conductivity of formation

Compute and compare the hydraulic conductivity (m/s) of a formation with respect to the three liquids below. The formation has a permeability k = 0.1 darcy and g = 9.8 m/s2. Liquid viscosity (g/cm s) density (g/cm3)

  Determine the expected speed of prototype to ensure numbers

A model of a submarine, at 1:15 scale, is to be tested at 0.8 ft/s in a wind tunnel at standard at mospheric pressure, while the prototype will be operated in seawater. Both the air and water are at 10 C (50 F).

  Plot the shape of water surface from the center to radius

a whirlpool is modeled as the combination of a free and a forced vortex. the maximum velocity in the whirlpool is 10 m/s, and the radius at the juncture of the free and the forced vortex is 10m.

  Calculate the pressure in point 1 and the density of fluid

A U manometer reads 20 cm air as operating fluid and a given manometric fluid. A single branch closed tube reads 35 cm connected to point 1. If P2 = 1.2 ATM calculate the pressure in point 1 and the density of the manometric fluid.

  Determine the landing speed of the airplane if it travels

A 32000 lb airplane lands on an aircraft carrier and is caught by an arresting cable. The cable is inextensible and is paid out at A and B from mechanisms located below deck and consisting of pistons moving in long oil-filled cylinders.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd