Water is critical to the paper production process

Assignment Help Civil Engineering

Reference no: EM13542344

The feed to VISY 8 Paper Mill comprises 450 tonne/day of waste paper (newsprint, brown boxes, ..). The paper is then pulped by mixing with clarified process water. The pulp (4 % paper fibre) then goes through stock preparation, screening and cleaning using process water prior to entering the paper machine. A variety of screens and hydrocyclones are used. The rejects from this stage go to either landfill (20 wet tonnes/d at 50% water) or are used as fuel for the boiler (60 wet tonnes/d). The pulp then enters the paper machine which consists of two major sections – wet end and dry end. In the wet end, water is removed by low pressure suction followed by pressing. A number of chemicals are added to the pulp just prior to entering the paper machine – these assist with the paper quality but their composition can be considered negligible for the purposes of the material balances.

After the wet end, the solids fraction in the paper is approx 20%. Following the wet end, the paper passes through the press section, where it is essentially pressed between large rollers which press the water out of the paper and onto the press ‘felt’ material. After the press, the solids content is between 35-50%. The dry end section consists of a number of steam-heated rollers which the paper passes over. After the dry end, the water content of the paper is 5-10%.

Water is critical to the paper production process, and it is used in most stages of the process.

Fresh water enters the process in 3 streams – approx. 0.5 ML/d enters with chemicals at the dry end of the machine, approx. 1 ML/d enters at the wet end of the machine and the boiler consumes approx. 0.2 ML/d.

There is a major water recycle system:

? The ‘clarified process water’ is used for pulping and the stock preparation, and it then enters the wet end of the paper machine with the pulp. It is separated in the wet end (suction and squeezing) as ‘process water’ and is treated in the clarification stage, which includes dissolved air flotation and sand air flotation. The flow rate entering the pulper is estimated as 9.7 ML/d. Is this correct?

? The ‘clarified process water’ is used for showers in the cleaning process of the stock preparation. The clarified water flow rate leaving the clarification section and returning to the stock preparation is approximately 25 ML/d.

The effluent (0.9 ML/d) from the clarification stage is treated in a UASB anaerobic wastewater treatment system on-site prior to discharge to the sewer for additional treatment at the Gibson Island sewage treatment plant. The UASB removes 80% of the solids that are present in the effluent from the clarification stage. The UASB produces biogas as a result of the anaerobic degredation of the solids and other compounds in the wastewater. The biogas (approx (150 Nm3/hr) is used as fuel in the boiler. The boiler also uses approximately 100 tonne/d of coal. The boiler produces 1000 tonnes/d of steam which is used for drying the paper (via heating the rollers). The condensate is returned to the boiler. The boiler produces 20 tonnes/d of ash.

Data: assume Biogas 40% CO2, 60% CH4; assume density of process water 1000 kg m-3

Reference no: EM13542344

Questions Cloud

Estimate the required stack height for wind speeds of 4 : A plant is to be constructed that will emit 3.5 metric tons of hydrogen sulfide per day. One of the design criteria is that the concentration 1 km downwind from the stack

Find the diameter of the tube to accomplish this : It is desired to transmit 300mm^3/s of gasoline at 20 degree Celsius through a 650mm long horizontal tube with a head loss of 500mm Find the diameter of the tube to accomplish this.

Find how many dimensionless parameters govern this problem : The flowrate Q over a rectangular sharp crested weir depends on the width of the notch b, the head on the weir H, and the acceleration due to gravity g.

Plot a curve showing the relationship of se versus : Plot a curve showing the relationship of Se versus L/r for steel columns. Draw the curve for slenderness ratios that vary from 0 to 200. Assume the proportional limit = 235 MPa

Water is critical to the paper production process : Fresh water enters the process in 3 streams – approx. 0.5 ML/d enters with chemicals at the dry end of the machine, approx. 1 ML/d enters at the wet end of the machine and the boiler consumes approx. 0.2 ML/d.

A conversion of land from tomato farming to cotton is plan : A conversion of land from tomato farming to cotton is planned. Is it true that less water will be used to supplement rainfall based on one growing season ?

Calculate the sequent depth required to form a jump with : Assuming a drag coefficient Cd of 0.6 for the baffle blocks based on the upstream velocity and combined frontal area of the blocks, calculate the sequent depth required to form a jump with the blocks and compare this value to the sequent depth requir..

Determine the average shear stress in each pin : The pins on the frame at B and C each have a diameter of 0.25 in. If these pins are subjected to double shear, determine the average shear stress in each pin.

Should hole a be placed to make the net wind force zero : In strong winds the force can be quite large. Suppose that a hole is introduced in the building’s roof at point A to make pi equal to the surface pressure there. At what angle ? should hole A be placed to make the net wind force zero?

User Account

All Pages