Water flows at 50oc inside a 25-cm-inside-diameter tube

Assignment Help Mechanical Engineering
Reference no: EM13625371

1.Water flows at 50oC inside a 2.5-cm-inside-diameter tube such that hi= 3500 W/m2 oC. The tube has a wall thickness of 0.8 mm with a thermal conductivity of 16 W/m2 oC. The outside of the tube loses heat by free convection with ho = 7.6 W/m2 oC. Calculate the overall heat-transfer coefficient and heat loss per unit length to surrounding air at 20oC.

2. Two 3.0-cm-diameter 304 stainless-still bars, 10 cm long, have ground surfaces and are exposed to air with a surface roughness of about 1 ?m. If the surfaces are pressed together with a pressure of 50 atm and the two-bar combination is exposed to overall temperature difference of 100oC, calculate the axial heat flow and temperature drop across the contact surface.

Reference no: EM13625371

Questions Cloud

Calculate the moment mn-m on the door hinge post on line : a ship channel has a depth of 16 m and an upper width of 16 m. the sides of the channel are curved such that the width
Use exponential smoothing with alpha 2 and the smoothed : the following data summarizes the historical demand for a productmonthactual
A rigid insulated vessel is divided into two compartments : a rigid insulated vessel is divided into two compartments connected by a valve. initially one compartment occupying
What would the mole and mass fractions be if she was to : a combustion engineer wishes to produce an inert mixture to replace normal air. she will do that using a mixture of n2
Water flows at 50oc inside a 25-cm-inside-diameter tube : 1.water flows at 50oc inside a 2.5-cm-inside-diameter tube such that hi 3500 wm2 oc. the tube has a wall thickness of
She knows that a high wind reduces the air pressure on the : dorothy is up on her 11.0m by 14.0m roof enjoying the view of kansas. suddenly a strong wind blows down her ladder
Assuming the process is adiabatic is this process possible : a vortex tube is used to separate an ideal gas at 10 bar and 375 k such that half the gas is collected in a cool stream
The cube has sides of lenght l100cm the electric field is : the cube has sides of lenght l10.0cm. the electric field is uniform has the magnitude e 4.00 x 103 nc and is parallel
Steam enters a steady flow turbine at 30mpa 1000degc with a : steam enters a steady flow turbine at 30mpa 1000degc with a flow rate of 10kgs. thirty percent of the inlet mass of

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd