Water executes a carnot power cycle

Assignment Help Mechanical Engineering
Reference no: EM13717269

One-half kilogram of water executes a Carnot power cycle. During the isothermal expansion, the water is heated until it is a saturated vapor from an initial state where the pressure is 1.5 MPa and the quality is 25%. The vapor then expands adiabatically to pressure of 100 kPa while doing 403.8 kJ/kg of work.

a) Evaluate the heat and work for each process, in kJ.

b) Evaluate the thermal efficiency.

Reference no: EM13717269

Questions Cloud

List three research obligations for research participants : List three research obligations for research participants, researchers, and research clients; explain why these obligations are important.
Define and give the dimensions of thermal conductivity : Define and give the dimensions of thermal conductivity k, thermal diffusivity a,heat capacity C, heat flux q, and combined energy flux e. For the dimensions use m = mass, I = length, T = temperature, and t = time.
Executes a power cycle while operating between reservoirs : An inventor claims to have developed a device that executes a power cycle while operating between reservoirs at 500 and 300 K that has a thermal efficiency of (a) 45%, (b) 40%, (c) 35%. Evaluate the claim for each case.
The task of reengineering a process : If you were charged with the task of reengineering a process, would you be concerned with integrating only the outcomes of parallel activities that must eventually come together? Defend your response.
Water executes a carnot power cycle : One-half kilogram of water executes a Carnot power cycle. During the isothermal expansion, the water is heated until it is a saturated vapor from an initial state where the pressure is 1.5 MPa and the quality is 25%. The vapor then expands adiabatica..
Determine the minimum theoretical operating cost : When the outside temperature is -10°C, a residential heat pump must provide 3.5 x 106 kJ per day to a dwelling to maintain its temperature at 20°C. If electricity costs 8 cents per kWh, determine the minimum theoretical operating cost for each day of..
Energy equation is an expression of conservation of energy : The Energy Equation is an expression of conservation of energy. However, the terms of the equation have dimensions of length. Each of the terms is called “head”. Discuss in your own words how each of these “head terms” relate to energy, and how the o..
Determine the mass flow rate of the refrigerant : Refrigerant 134a flows at steady state through a horizontal tube having an inside diameter of .05 m. The refrigerant enters the tube with a quality of .1, temperature of 36 C, and velocity of 10 m/s. The refrigerant exits the tube at 9 bar as a satur..
Rdt and it analysis outline and annotated bibliography : With your RDT and IT Analysis Outline and Annotated Bibliography, you will demonstrate the research you have completed in your course project and receive instructor feedback. Your annotated bibliography should be annotative, as opposed to summa..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The pressure is held constant as the air cools to 50degc

the pressure and temperature of the air entering the condenser are 800 kpa and 150degc respectively. the pressure is

  The development of flight dealt with the design

The development of flight dealt with the design of the propeller

  A fenced enclosure consists of a rectangle of length l and

a fenced enclosure consists of a rectangle of length l and width 2r and a semicircle of radius r as shown in figure

  Max theoretical efficiency of a coal fired plant

A conventional coal fired power plant has a thermodynamic efficiency of 30%. If coal burns at 400C, what's the max theoretical efficiency of a coal fired plant.

  Calculate the battery failure probability under normal

a particulate monitor has a power supply consisting of two batteries in parallel. either battery is adequate to

  Plot the moment about b

Plot the moment about B for 320mm

  Find the maximum shear stress

Find the maximum shear stress in a 5 1/2 in-diameter circular saw blade if it runs idle at 5000 rev/min. The saw is 14 guage(0.0747 in) steel and is used on a 5/8 in-diameter. The thickness is uniform. What is the maximum radial component of stress?

  With a safety factor of 4 what axial compressive load can

a 1x2-in bar is 20 in. long and made of steel with sy 25ksi. with a safety factor of 4 what axial compressive load can

  Show work to prove the following problem an experimentalist

show work to prove the following problem an experimentalist claims to have raised the temperature of a small amount of

  Design a computer programme using freudestein equation

design a computer programme using freudestein equation to synthesise a four bar linkage using three precision points also using more than three points.

  After a period of time the pressure in the tank rises to 15

initially an insulated rigid tank contains 3.73 kg of water at 240oc and 1 mpa. a heater in the wall of the tank

  A cylindrical specimen of a metal alloy

A cylindrical specimen of a metal alloy 51.3 mm long and 11.1 mm in diameter is stressed in tension. A true stress of 350 MPa causes the specimen to plastically elongate to a length of 57.9 mm. If it is known that the strain-hardening exponent for th..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd