Voltage on vertical axis-current on horizontal axis

Assignment Help Mechanical Engineering
Reference no: EM13704760

1. Using the graph paper provided, plot graph of voltage vs, current for the data in each table. Plot the entire graph on the same axes with voltage on the vertical axis and current on the horizontal axis.

What is the similarity between these graphs? What does the slope of each graph represent?

2. How do the measured current for each resistance compare with the calculated values? Explain any discrepancies.

3. From the graphs, calculate the resistance for each value of R at a current level of 5mA. How do these values compare to the theoretical resistance values?

Reference no: EM13704760

Questions Cloud

The water is then condensed isothermally to saturated liquid : Water vapor initially at 3.0 MPa and 300 C is contained within a piston-cylinder assembly. The water is cooled at constant volume until its temperature is 200 C. The water is then condensed isothermally to saturated liquid. For the water as the syste..
Determine the rate of steam flow-back-pressure steam : A 20 MW back-pressure steam turbine receives steam at stagnation pressure of 4 MPa and stagnation temperature of 300oC, exhausting from the last stage at stagnation pressure of 0.35 MPa. The turbine isentropic efficiency is 0.884, and mechanical loss..
Create a pressure-enthalpy diagram : Create a Pressure-Enthalpy diagram for R134a. Be sure to show the saturated liquid line and the saturated vapor line together so that the entire saturation dome is displayed. Also include an isotherm, for t=70c, that extends from within the saturated..
Determine displacement of in diameter steel bar : Determine displacement (in) of a 1.08 in diameter steel bar, which is 834 ft long under a force of 33,222 lb if elasticity modulus is 30 x 106 psi. Make sure you do not round up your answer to less than 4 significant (non-zero) figures.
Voltage on vertical axis-current on horizontal axis : Using the graph paper provided, plot graph of voltage vs, current for the data in each table. Plot the entire graph on the same axes with voltage on the vertical axis and current on the horizontal axis. What is the similarity between these graphs? Wh..
Find its speed and the magnitude : Given that the station is on average 420 km above the Earth find its speed (in m/s) and the magnitude of centripetal acceleration
How high did the ball rise : You throw a ball vertically upward at 27.0 m/s, and then catch it at the same height you released it. Ignoring air resistance, how high did the ball rise
Evaluate how much energy is stored in the capacitor : A 3.0-V battery is connected to a 3.20-µF capacitor. How much energy is stored in the capacitor
Calculate the velocities of the water at the two holes : There are two holes in the side of a bucket, one is 10 cm below the surface, and the other is 20 cm below. Calculate the velocities of the water at the two holes

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd