Vertical piston cylinder is heated at constant pressure

Assignment Help Mechanical Engineering
Reference no: EM13711511

Water in a vertical piston cylinder is heated at constant pressure of 10 bar. It is initially at 179.9 0C and has a specific volume of 0.1 m3/kg and is heated to a final specific volume of 0.248 m3/kg. Changes in kinetic and potential energies are zero. Determine

a) sketch in a T-V and P-V diagram

b) the initial quality of water

c) the final temperature of the water vapor

d) the work in kJ/kg

e) the initial and final internal energy in kJ/kg

f) the heat transfer in kJ/kg

Reference no: EM13711511

Questions Cloud

Calcium silicate has replaced asbestos preferred insulation : Calcium Silicate has replaced asbestos as the preferred insulation for steam lines in power plants. Consider a 40 cm O.D., 4 cm wall thickness steel steam line insulated with a 12 cm thickness of calcium silicate. The insulation is protected from dam..
Determine the mass flow rate through the compressor : Carbon Dioxide (CO2) gas enters a compressor steadily at 10 KPa and 540K with a velocity of 200m/s. The carbon dioxide leaves the compressor at 3MPa and 900K with a velocity of 40m/s. The exit of the compressor is .006m^2. The heat transfer rate from..
For mass-spring-damper accelerometer : For mass-spring-damper accelerometer, calculate the mass needed to achieve mechanical noise limit a_rms = 1 nG if the mechanical resonance frequency is to be f=100 Hz.
Gas in a closed system undergoes the power cycle : Gas in a closed system undergoes the power cycle as shown in the p-v diagram below as described by 1->2 is a constant pressure process, 2-> 3 is a constant volume process and 3 -> 1 is a pV = const. process. The internal energy U1 = U2 = 30 kJ/kg and..
Vertical piston cylinder is heated at constant pressure : Water in a vertical piston cylinder is heated at constant pressure of 10 bar. It is initially at 179.9 0C and has a specific volume of 0.1 m3/kg and is heated to a final specific volume of 0.248 m3/kg. Changes in kinetic and potential energies are ze..
Measured in frequency bands of constant width : White noise has a constant level when measured in frequency bands of constant width. Suppose a noise generator produces white noise over the octave bands 0.5,1,2,4,8 khz. Find the overall un weighted and a-weighted sound pressures if a sound pressure..
Single-stage ideal regenerative steam cycle : A single-stage ideal regenerative steam cycle has a boiler pressure and temperature of 5000 kPa and 500 C, and a condensing pressure of 10 kPa. The extraction pressure is 500 kPa.
The temperature of the gases leaving the compressor : A diesel engine is fitted with a turbocharger that comprises a radial flow compressor driven by a radial flow exhaust gas turbine. The gravimetric air-fuel ratio is 20:1; the air is drawn into the compressor at a pressure of 1 bar and at a temperatur..
Estimate the molar volume of isobutane at initial : Saturated isobutane vapor at 320 K is contained in a piston-cylinder assembly. It is expanded to 3 bar by a reversible isothermal process. At 320 K, the vapor pressure of isobutane is 6.243 bar. Using the truncated virial equation of state, i.e. with..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If the coefficient of static friction between the beam and

the uniform beam of mass 40 kg is supported by the rope which is attached to the end of the beam wraps over a rough peg

  Apply the newton-raphson method to the function fx tanhx2-9

a apply the newton-raphson method to the function fx tanhx2-9 to evaluate its known real root at x3. use an initial

  How much water must be injected to reduce the pressure in

a rigid insulated 1.4 m3 container initially contains steam at 1.4 mpa and a quality of 85. liquid water at 10 deg c is

  What will be the charge on the capacitor a long time after

capacitor with capacitance 6.00 microf is connected to a resistor with r 780 o in series and an emf source of 25.0 v

  Calculate the engineering strain and the true strain for

a solid cylindrical specimen 200-mm high is compressed to a final height of 60 mm in two steps between frictionless

  Determine the rate of heat addition and rejection for this

an otto cycle uses air as the working fluid its state at the beginning of the compression is 14 psia and 60 degrees f

  A water cooled spherical object of diameter 10 mm and

a water cooled spherical object of diameter 10 mm and emissivity 0.9 is maintained at 4000c. what is the net transfer

  A homogeneous liquid solidifies directly to a solid

a friend asks you to construct the phase diagram for a new binary alloy of a and b. the clues are i a and b are

  What is the drag coefficient of the model also calculate

a 14 scale model of a tractor trailer is tested in a wind tunnel under standard sea level conditions. the model

  A long cylinder pressure vessel with closed ends has an

a long cylinder pressure vessel with closed ends has an internal pressure of 3 mpa. calculate the hoop stress sigma

  Method available-australia to protect intellectual property

Prepare a report on the various types of methods available in Australia to protect intellectual property - The strategy's main items should include what to protect, what countries to protect it in, how to protect it, and when to seek protection

  What is the maximum useful work that can be produced per

what is the maximum useful work that can be produced per pound of saturated steam which enters a steady flow system at

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd