Verify this calculation of drag coefficient estimate the

Assignment Help Mechanical Engineering
Reference no: EM13640511

The resistance to motion of a good bicycle on smooth pavement is nearly all due to aerodynamic drag. Assume that the total mass of rider and bike is M = 100 kg. The frontal area measured from a photograph is A = 0.46 m2. Experiments on a hill, where the road grade is 8 percent, show that terminal speed is Vt = 15 m/s. From these data, drag coefficient is estimated as CD = 1.2. a) Verify this calculation of drag coefficient. B) Estimate the distance needed for the bike and rider to decelerate from 15 to 10 m/s while coasting after reaching level road.

Reference no: EM13640511

Questions Cloud

All test specimens were 15 inches in diameter and 3 inches : on a grap paper draw the mohrs circle of stress for a uniaxial test and two triaxial test in which the maximum
Calculate methane obeys the virial equation of state z : an insulated and non-conducting tank of volume 1m3 is initially evacuated. it is connected by a valve to supply line
Evaluate the power needed to overcome this force use : a jet transport aircraft cruises at 12 km altitude in steady level flight at 820 kmhr. model the aircraft fuselage as a
A plane flies at an airspeed of 255 kmh a wind is blowing : a plane flies at an airspeed of 255 kmh. a wind is blowing at 75 kmh toward the direction 60deg east of north.a in what
Verify this calculation of drag coefficient estimate the : the resistance to motion of a good bicycle on smooth pavement is nearly all due to aerodynamic drag. assume that the
Two students a and b are both registered for a probability : two students a and b are both registered for a probability class. neither student has a sterling attendance pattern.
Determine for the cycle the mass flow rate of condenser : water is the working fluid in an ideal rankine cycle. superheated vapor enters the turbine at 8 mpa 480 oc. the
Water drips from the nozzle of a shower onto the floor 203 : water drips from the nozzle of a shower onto the floor 203 cm below. the drops fall at regular equal intervals of time
A bullet is fired through a board 140 cm thick with its : a bullet is fired through a board 14.0 cm thick with its line of motion perpendicular to the face of the board. if it

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd