Value of the thermal resistance

Assignment Help Mechanical Engineering
Reference no: EM13947489

1. The fin array of Problem 3.142 is commonly found in compact heat exchangers, whose function is to provide a large surface area per unit volume in trans- ferring heat from one fluid to another. Consider conditions for which the second fluid maintains equiva- lent temperatures at the parallel plates, TTL, thereby establishing symmetry about the midplane of the fin array. The heat exchanger is 1 m long in the direction of the flow of air (first fluid) and 1 m wide in a direction normal to both the airflow and the fin surfaces. The length of the fin passages between adjoining parallel plates is = 8 mm, whereas the fin thermal conductivity and convection coefficient are = 200 W/m · K (aluminum) and = 150 W/m2 · K, respectively.

2. If the fin thickness and pitch are = 1 mm  and = 4 mm, respectively, what is the value of the thermal resistance Rt,o for a one-half section of the fin array?

3. Subject to the constraints that the fin thickness and pitch may not be less than 0.5 and 3 mm, respec- tively, assess the effect of changes in and S.

Reference no: EM13947489

Questions Cloud

Recommend a design that enhances chip cooling : The top of the burner is exposed to room conditions (Tsur,t = Too,t = 20°C, ht = 40 W/m2 · K), while the bottom of the burner is exposed to combus to ensure adequate airflow passage through the array. Recommend a design that enhances chip cooling.
Reorder the data to reflect income statement format : From the text " Fundamentals of Healthcare Finance" 2nd edition by Louis C. Gapenski, page 352 end of chapter problem 11.1. Entries for the Warren Clinic 2012 income statement are listed below in alphabetical order. Reorder the data to reflect income..
Discuss whether the solution right for the target audience : Be sure to identify the target audience and discuss whether the solution seemed appropriate for the target audience.
Balance in investment account would be equal to the cost : Phan Company owns 28% of the common stock of San Company and accounts for the investment using the equity method. Assuming that Phan Company purchased the stock several years ago, the balance in the investment account would be equal to the cost of th..
Value of the thermal resistance : If the fin thickness and pitch are t = 1 mm  and S = 4 mm, respectively, what is the value of the thermal resistance Rt,o for a one-half section of the fin array?
What is the probability of an odd sum : Two numbers are randomly drawn from (1, 2, 3, ..., 10) with replacement and added together. What is the probability of an odd sum?
Growth stocks outperform value stocks : Even though no final conclusion is currently warranted, a number of research papers, including those of Fama and French, have argued that: there is no noticeable difference in the returns of growth versus value stocks. growth stocks outperform value ..
Determine the fin heat transfer rate : A 40-mm-long, 2-mm-diameter pin fin is fabricated of an aluminum alloy (k = 140 W/m · K). (a) Determine the fin heat transfer rate for Tb = 50°C, Too = 25°C, h = 1000 W/m2 · K, and an adiabatic tip condition.
What is the expected waiting time to first birth : Assume that the probability of conception in any given month among sexually active couples not practicing birth control is constant at 0.20 per month, independent of the number of months the couple has been active. what is the expected waiting tim..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd