User Account

All Pages

Validate a reusable component

Assignment Help Mechanical Engineering
Reference no: EM13888763

Explain why it is difficult to validate a reusable component without the component source code. In what ways would a formal component specification simplify the problems of validation?

Design the ‘provides' interface and the ‘requires' interface of a reusable component that may be used to represent a patient in the MHC-PMS.

Reference no: EM13888763

Questions Cloud

Major technical and nontechnical factors : What are the major technical and nontechnical factors that hinder software reuse? Do you personally reuse much software and, if not, why not?
Independent certification authority : It has been suggested that an independent certification authority should be established. Vendors would submit their components to this authority, which would validate that the component was trustworthy.
Determine the target cost per unit for the filter : Krystal Water is considering introducing a water filtration device for its 20-ounce water bottles. Determine the target cost per unit for the filter.
Different types of adaptor : Using examples, illustrate the different types of adaptor needed to support sequential composition, hierarchical composition, and additive composition.
Validate a reusable component : Explain why it is difficult to validate a reusable component without the component source code. In what ways would a formal component specification simplify the problems of validation?
Find and critique an empirical article : Find and critique an empirical article in which a factor analysis was used to build a leadership/organizational instrument (scale) that was published in a peer-reviewed leadership journal. Then, start the dialogue by critiquing the selected resear..
Program elements and components : 1. What are the fundamental differences between components as program elements and components as services? 2. Why is it important that components should be based on a standard component model?
What the legal challenges were for the slaves in the amistad : what the legal challenges were for the slaves in the Amistad case
Principle of component independence : The principle of component independence means that it ought to be possible to replace one component with another that is implemented in a completely different way. Using an example, explain how such component replacement could have undesired conse..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Calculate the work done and the final temperature

Calculate the work done and the final temperature for the following processes: Polytropic, n = 1.1, 4.0 lbm of Air, T1 = 1300 °F, v1=6.519 ft3/lbm. The pressure decreases to half the initial pressure during the process.

  Steam power plant operates on the ideal reheat rankine cycle

A steam power plant operates on the ideal reheat Rankine cycle. Steam enters the high pressure turbine at 6 MPa and 4000C and leaves at 2 MPa. Steam is then reheated at constant pressure to 4000C before it expands to 20 kPa in the low pressure turbin..

  How much energy in ft-lbf btu and kj is required to

how much energy in ft-lbf btu and kj is required to accelerate my 3400 pound car from rest to a velocity of 60 mph on a

  If a sludge containing 70 water and 30 solids is passed

sludge is wet solids that result from the processing in municipal sewage systems. the sludge has to be dried before it

  Turbulent-flow velocity data

The following turbulent-flow velocity data u(y), for air at 75°F and 1 atm near a smooth flat wall, were taken in the University of Rhode Island wind tunnel:

  The piston rises to a new position doing 100 j of work on

a cylinder with a movable piston contains a gas. initially the gas temperature is 25 c. a two stage process happens. in

  If the energy of the system were to be changed this same

can we boil water by dropping it off a cliff? for 1 kg of liquid water at room temperature 25 oc determine the change

  In metal injection molding what is the green part made of

In metal injection molding what is the green part made of?, when is the green part made?, how is a brown part created?, and how does the final metal molded part become fully dense with cast metal properties?

  Find the minimum value of the relative humidity in the room

A person with glasses enters a heated room at 22oC, after spending some time in the cold (the glasses are at 1oC). The glasses start to fog. Find the minimum value of the relative humidity in the room.

  Compute the fugacity of pure liquid water

Calculate the fugacity of liquid hydrogen sulphide in contact with its saturated vapor at 25.5C and 20 bars. The vapor pressure of pure water at 310.6 K is 6.455 kPa. Compute the fugacity of pure liquid water at 310.6 K when it is under a pressure of..

  Determine the rate of entropy generation ie irreversibility

a car traveling at highway speed assume 60 miles per hour 1 mile 5280 ft must overcome a drag force of approximately

  Three grams of air are contained in a piston-cylinder

three grams of air are contained in a piston-cylinder. initially the air temperature and volume are 300k and 2.5 liter.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd