Using the mechanical energy balance estimate the time

Assignment Help Mechanical Engineering
Reference no: EM13606960

Using the mechanical energy balance, estimate the time required for the water level to drop from an upper piece of tape (42.0cm) to the lower peice of tape (34.0cm) on a cylindrical tank. The diameter of the tank is 30.0cm. At the bottom of the tank there is a cylyndrical pipe (0.9 cm diameter) extending from the bottom of the tank into a bucket (32cm below the tank). This pipe has a valve attached to it that controls the flow of the water out of the tank. Neglect frictional losses.

Reference no: EM13606960

Questions Cloud

Determine the direct materials price variance direct : the following data relate to the direct materials cost for the production of 2000 automobile tiresactual 54600 lbs at
A an egg is thrown nearly vertically upward from a point : a an egg is thrown nearly vertically upward from a point near the cornice of a tall building. it just misses the
Posterscom is a small internet retailer of high-quality : posters.com is a small internet retailer of high-quality posters. the company has 1000000 in operating assets and fixed
Angies blooms purchased a delivery van for 30000 the : angies blooms purchased a delivery van for 30000. the company was given a 3000 cash discount by the dealer and paid
Using the mechanical energy balance estimate the time : using the mechanical energy balance estimate the time required for the water level to drop from an upper piece of tape
A building was purchased on january 1 1998 for 240000 and : a building was purchased on january 1 1998 for 240000 and straight line depreciation method was used. it was estimated
Finished goods inventory is 190000 if overhead applied to : finished goods inventory is 190000. if overhead applied to these goods is 72000 and the overhead rate is 120 of direct
Wesley hospital installs a new parking lot the paving cost : wesley hospital installs a new parking lot. the paving cost 40000 and the lights to illuminate the new parking area
Methane ch4 has a tetrahedral structure similar to that of : methane ch4 has a tetrahedral structure similar to that of si02 with a carbon atom of radius 0.77x10-8 cm at the center

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd