Using multisim construct the circuits

Assignment Help Other Engineering
Reference no: EM131077342

INTRODUCTION

Which types of applications are field-effect transistors preferred over bipolar junction transistors? Why?  Explain why junction field-effect transistors are considered voltage-controlled devices.

EQUIPMENT

  • 1 power supply: 15V
  • 1 transistor: 2N4860
  • 3 resistors: 1k?, 4.7k?, 2M?
  • <List meters used>

PROCEDURE

Using Multisim construct the circuits shown below:

Measure the following and record the values in the "results" section: VG, ID, VS, VD, VDS,

RESULTS

Calculate VGS from the measured values.

Which type of biasing is used?

The table below shows readings for three different cases where the circuit above, was malfunctioning. Find the fault, assuming only one device in each case has a problem. List the steps taken to arrive at a solution.

 

VDS

VD

VS

What is the problem?

1

91.4mV

91.4mV

0V

 

2

66.5mV

15V

14.9V

 

3

15

15

0

 

Reference no: EM131077342

Questions Cloud

Difference between multiprogramming and multi-threading : Under what circumstances would you choose to use an interpreted language?
Find expressions for u and v in terms of x and y : Math 121A: Homework 2. The complex numbers z and w are related by w = 1 + iz/i + z. Write z = x + iy and w = u + iv where u, v, x, and y are real. Find expressions for u and v in terms of x and y
Find the length of a pendulum : A grandfather clock with short vertical pendulum is being carried by a maglev train, which accelerates ?or 10 s with a g. The train then coasts for some time, followed by breaking with deceleration a = -g until stopping. Will the clock lose or gai..
Implement in c++ the external merge sort algorithm : Extend your implementation of externalMergesort by removing the restriction that the fi le contains 2n blocks.
Using multisim construct the circuits : Which types of applications are field-effect transistors preferred over bipolar junction transistors? Why?  Explain why junction field-effect transistors are considered voltage-controlled devices.
What does ifconfig do in linux : 1. What does ifconfig do in Linux? 2.What are the ranges used for private ip addressing.
How is inventory described for your sec company : How is inventory described for your SEC 10-K company? LIFO, FIFO, and / or average cost? Relate your answer to topics in our course. Cost and sources for production materials: notice how cost is used in the SEC 10-K.
Charge of computer support : Your team is in charge of computer support at a major U.S. retailer. Business has been growing fast, and your company is about to open several new facilities across the country.
Reasons why the company needs a security plan : Prepare a 15-slide presentation with speaker notes for Senior Management that will provide an outline for a Security Guidance plan encompassing best practices from key areas that were covered in this course.

Reviews

Write a Review

Other Engineering Questions & Answers

  How biometrics is used in the medical field

Biometrics is the science of using one or more unique physical characteristics or behavioral traits to identify and verify individuals. The best-known biometric identification method is fingerprinting (National Institute of Justice, 2011). Biometr..

  What fraction of the chip is occupied by the i/o connections

A 1.5-V, 1-Gbit dynamic RAM (called DRAM) by Hitachi uses a 0.16-μm process with a cell size of 0.38× 0.76 μm2 in a 19×38 mm2 chip. What fraction of the chip is occupied by the I/O connections, peripheral circuits, and interconnect?

  What was the historical scope of telecommunications

What was the historical scope of telecommunications?

  What the advantages of digital signals over analog signals

What are the advantages of digital signals over analog signals? Cover noise suppression in your explanation

  Takeoff and landing performance

What is the rule of thumb increase in takeoff distance and rotation speed in percentage and what is the climb gradient (%) and climb angle (deg)?

  Draw the free-body diagram

Draw the free-body diagram of the 50-kg paper roll which has a center of mass at G and rests on the smooth blade of the paper hauler. Explain the significance of each force acting on the diagram. (SeeFigure)

  Design the appropriate architecture for the project

You are required to design an energy meter based on CPLD (Complex Programmable Logic Device) that will smartly disconnect the supply when sufficient amount of energy units are consumed. The device needs to be programmed using VHDL computing language.

  Formulate an integer linear programming model

Formulate an integer linear programming model for Dr. Konur's problem by defining your decision variables, and expressing your objective and objective function

  Write essay on solar powered motor boat

This question in Engineering is about an essay on Solar Powered Motor Boat. In the recent times due to increase in pollution as well as increasing cost of fossil fuels are forcing engineers and scientists look for alternative and sustainable sourc..

  Adequacy of the section to carry the load combination

Determine the adequacy of the section to carry the load combination of dead and live load. Assume the ends of the beam are fully restrained.

  Use superposition to calculate the dc voltage

Wire the circuit and connect a scope probe at X, be sure to DC couple the input and set the ground level at the bottom of the scope display, then sketch the results.

  Describe the normal single chip operating mode and indicate

a describe the normal single chip operating mode and indicate how this mode can be selected.b describe the normal

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd