Use the conveyance method to verify the results

Assignment Help Civil Engineering
Reference no: EM13545659

A drainage channel had a cross section that may be approximated as a trapezoidal section with a bottom width of 15 feet and a side slope of 1.5H:1V. If the channel drops 2.5 feet per mile, compute the flow depth for a flow of 150 cubic meters per second. Assume a Manning n=0.024. Use the conveyance method to verify the results.

Reference no: EM13545659

Questions Cloud

How many cubic yards of aggregate must be ordered for a road : How many cubic yards of aggregate must be ordered for a road base 16 inches thick and 2000 feet long with a top width of 30 ft, if the side slopes are one on one, or 45 degree?
What major differences would you expect if the water supply : A large stream flowing through a highly industrialized area must serve as the source of a community's water supply. The turbidity of the water ranges from 30 to 60 NTU, alkalinity exceeds 100 mg/L.
Determine the coliform concentration at the beach : Determine the coliform concentration at the beach. (assume that the current behaves as a plug flow reactor and that the wastewater is completely mixed in the current at the discharge point.
What is the discharge of each hole : A water of 20 c temprature pupped at 75 kpa to a perforated pipe 5 cm dia. contain 10 hole with the same diameter. the distance between two adjacent hole is 20 cm. what is the discharge of each hole?
Use the conveyance method to verify the results : A drainage channel had a cross section that may be approximated as a trapezoidal section with a bottom width of 15 feet and a side slope of 1.5H:1V. If the channel drops 2.5 feet per mile.
Determine the size of the watershed in acres and then : The 1-hr UH in the table was recorded for a particular watershed. Determine the size of the watershed in acres and then convert the 1-hr UH into a 3-hr UH for the watershed.
Determine the magnitude of the largest elastic load p that : The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. the outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. if the yield stress for the steel is
What is the maximum weight of the crate that the system can : Rope BCA passes through a pulley at point C and supports a crate at point A. Rope segment CD supports the pulley and is attached to an eye anchor embedded in a wall. Rope segment BC creates an angle of = 74.0 with the floor and rope segment CD
Find the capacity of the column with 1% reingforcement : A circulatr concrete column with a diameter of 8" has spiral reinforcing. Find the capacity of the column with 1% reingforcement. Find the capacity of the column with 8% reinforcement.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Determine what is the maximum queue length

Vehicles arrive at the booth at a rate of 4 vehicles per minute. The attendent opens the booth and improves the service rate over time following the function u(t)= 1.1 +0.3t, where u(t) is in vehicles per minute and t is in minutes.

  Show how kh and kow can be used to describe koa

Show how Kh, and Kow can be used to describe Koa. You must show how the concentration units for all equilibrium distribution ratios either cancel or remain to give the final value for Koa. Octonal-air partitioning coefficient (Koa = C(octanol)/C(a..

  Compute the max possible moment at the centerline

compute the max possible moment at the centerline of the beam and the absolute moment in the beam.

  What is the magnitude and direction of the resultant force

The bend lies in a horizontal plane, and water enters from the west and leaves toward the north. Assuming no drop in pressure, what is the magnitude and direction of the resultant force acting on the bend

  Determine the weight of bar for distance between two base

The bar is 1m long and its weight, W, acts at its midpoint. The angle is a=30 degrees, and the the spring constant k= 100N/m. The spring in its current position is 1.52m long, and its unstretched length of 1.25 m occurs when the bar is vertical a=..

  Find the depth and change in water surface elevation caused

Water is flowing at a depth of 10 ft with a velocity of 10 ft/s in a channel of rectangular section. Find the depth and change in water surface elevation caused by a smooth upward step in the channel bottom of 1 ft.

  Plot the normalized concentration versus normalized time

Write the mass balance equation for a completely mixed lake with an impulse input of mass, M, added at time t = 0. Assume the lake is of constant volume, V, with continuous outflow, Q, and a conservative substance.

  What is the maximum weight that can be suspended on poll

What is the maximum weight that can be suspended on a 16 Kg poll, 3/5 from the end. The maximum tension of the 30 degree guy-wire is 1500 N. Find the horizontal and vertical forces exerted on the poll by the hinge.

  What is the range of water contents of the in-situ soil that

The specifications for a project specify that the in-situ soil must be compacted to 98% of its maximum Modified Proctor Density. What is the range of water contents of the in-situ soil that will meet this criteria?

  Determine the combined amounts of water evaporated

while groundwater andinfiltration losses over the period were estimated to be 0.6 inches. Determine the combined amounts of water evaporated and transpired from the region during the year of record.

  Determine the number of gallons of paint needed to paint

Determine the number of gallons of paint needed to paint the outside surface of the water-supply tank, which consists of a hemispherical bottom, cylindrical sides, and a conical top. Each gallon of paint can cover 250 ft^2

  Determine what is the stress at the bottom of the tank

A steel cylinder tank is 10 ft in diameter, 15 ft high, and is filled with a brine solution. Brine weighs 10 lbf/gal. The thickness of the steel shell is 1/2 in. The cylinder sits on a concrete pad 12ft x 12ft .

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd