Use the bernoulli equation

Assignment Help Civil Engineering
Reference no: EM13210545

A venturi meter is placed in a pipeline to measure the flow rate of the liquid flowing through that pipe.The meter inlet and throat are connected by the two legs of a mercury manometer. Use the Bernoulli equation to describe how this manometer can be used to measure the flow rate through the meter.

Reference no: EM13210545

Questions Cloud

Discuss the challenges faced by the manager : Discuss the challenges faced by the manager in terms of : Communication skills ,Cultural, Policies or legislations ,Infrastructure , labour laws or any other challanges.
Harvey wasserman-the robber barons : Write paper on article: American Perspectives - Harvey Wasserman, “The Robber Barons”
What is the astronomic azimuth of the line : The magnetic north azimuth of a line is 128 degrees 27' while the magnetic declination is 3 degrees 30'E. What is the astronomic azimuth of the line (in decimal degrees)?
What is the length of the partial wavelength : What is the length of the partial wavelength for electromagnetic energy with a frequency of 15 MHz and a phase shift of 263 degrees (in meters)?
Use the bernoulli equation : Use the Bernoulli equation to describe how this manometer can be used to measure the flow rate through the meter.
What length l of splice plate is needed : two strips of a plastics material are bonded together as shown. The average shearing stress in the glue must be limited to 1000 kpa. what length L of splice plate is needed if the axial load carried by the joint is 55 kN and the width (W) is 315 m..
Determine the quality of the initial state : A two-phase liquid-vapor mixture of water is initially at a pressure of 10 bars. If on heating at fixed volume, the critical point is attained, determine the quality of the initial state.
Project to develop themselves professionally : Learning how to get a high performing team will require a lot of effort by the project manager. As a Project Manager, how would you balance your efforts to get the project done with your efforts to help team members use their work on the project to d..
Risks can occur any time in the project life cycle : We all know that there will be risks can occur any time in the project life cycle.

Reviews

Write a Review

Civil Engineering Questions & Answers

  Principal stresses and the orientation of planes

A direct shear test is performed on a saturated specimen of loose sand. A normal stress equal to 100 kPa is applied and a maximum shear stress of 75 kPa is measured in the shear test. Determine the principal stresses and the orientation of these p..

  What is effect of packing factor in self compacting concrete

what is effect of packing factor in self compacting concrete?

  Maximum and minimum stress intensities in the section

Determine the maximum and minimum stress intensities in the section.

  Projectile shot vertically upward

The height (in meters) of a projectile shot vertically upward from a point 2 m above ground level with an initial velocity of 24.5 m/s is h2+24.5t-4.9t^2 after t seconds. a) When does the projectile reach its maximum height? b) What is the maximum..

  Magnitudes of the additional loads

Determine the magnitudes of the additional loads that must be applied at B and F if the resultant of all six loads is to pass through the center of the mat.

  Prtoblem on uniform decelerated motion

Assuming uniformly decelerated motion, determine the velocity and acceleration of point C of the belt, (a) immediately before the power is turned off. (b) 9 s later.

  Percent elongation and percent reduction in area

Also, at the failure cross sections the diameters are found to be 0.731 in., 0.645 in., and 0.587 in., respectively. Determine the percent elongation and percent reduction in area of each specimen.

  Determine the torsional buckling stress

determine the torsional buckling stress for the compression member if the length is 4m and cross section is the form shown. the ends are restrained such that there are not free to warp.given A:5646mm2 Ix:42.63Mmm4 Iy:14067Mmm4 E:210kN/mm2 G:80kN/m..

  Determine ft and fn

for this purpose replace this force by its equivalent of two forces at At Ft parallel and Fn perpendicular to the beam. Determine Ft and Fn.

  Tackling the problem of making tunnel

You are a Project Manager on site where work for 3K.m. long Tunnel has been undertaken. The site is remote and takes about 2 days travel to nearest town. Supervisors, Technicians & Skilled Workers are engaged in dangerous / hazardous work.

  Annual power cost of the ro system

Is the system within membrane manufacturer's warranty requirement of maximum flux rate of 14 gfd? What is the annual power cost of the RO system?

  Maximum deflection of the beam

Determine the deflection of the right end of the pointer and the maximum deflection of the beam.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd