Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
MEGN 481: Machine Design
1) he rotating 1050 cold rolled steel shaft shown in the figure below is simply supported at the center of two bearings (denoted by an X) and the only applied load is the constant 7kN load. All dimensions are in mm and all steps in the shaft have a 4mm fillet radius at the base of each step. Use the ANSI recommendations for keyway design. All three locations, A, B and C have a non-steady torque of Tmax=500N-m and a Tmin=400N-m that follows a sin wave (magically). Determine the safety factor for infinite life at locations A, B and C. The shaft is machined, used at room temperature and requires a material reliability of 99.9%. Assume all other correction factors are equal to 0.499 when multiplied together.
2) For the shaft shown below, disregard the diameters noted. You must completely design the section of the shaft enclosed in red. Specifically, you must determine the three shaft diameters (locations marked "b", "a", and the one between). The diameter of the stepped-up shaft between "b" and "a" cannot be greater than 1.25 times the larger of the two ("a" or "b"). You must design to a FoS=2.5. You must determine an appropriate radius for the transition between the smaller shaft diameters and the larger one (locations marked as "A" and "B" only). You must also specify the correct keyway for shaft section "a" (location marked "C"). Inputs to the system and B.C.'s are identical to those stated above in problem 1.
3) What are the maximum, minimum and average power values for the shaft shown below when l = 20, a = 16, b = 18, P = 1000, Tmin = 0 and Tmax = 2000 lbfin if shaft speed is 750 rpm?
Design an Initial conceptual model Dynamic designs, Initial conceptual model A full class diagram with a complete set of labelled associations, compositions and generalisation where appropriate. All associations should indicate correct multiplicities..
A 200-kg flywheel is at rest when a constant 300 N · m couple is applied. After executing 560 revolutions, the flywheel reaches its rated speed of 2400 rpm. Knowing that the radius of gyration of the flywheel is 400 mm, determine the average magni..
What are the five (5) fluids used as damping media. Calculate the logarithmic decrements of the beam in these five fluids. Calculate the damping ratio of these five fluids and rank them from the highest to the lowest.
Calculate the fracture stress (σc) for a crack length (2a) of 50 mm, assuming plane strain conditions. If conditions were plane stress instead.
An antenna having an input impedance on transmission of 70+j30 ohms is used on reception by connecting directly to a 50 ohms transmission line which is perfectly matched to a pure resistance load.
Contrast the work of Renoir and Laurtrec. How do the subjects' styles of the artists reflect nineteenth century French society and the innovations of nineteenth century art?
2. (h) Perform research on at least one engineering disaster or failure related to control. And answering the following questions: a. What was the engineering failure or disaster?
Determine the airflows and pressure drop in each of the branches and what are the flows and pressure drops in each of the branches?
Given a second class lever with a distance of 5' from the fulcrum to the effort and a distance of 33" from the resistance to the fulcrum, what is the maximum amount of weight that can be lifted with 25 lbs of effort?
Derive at least four concept designs to satisfy the given specification. Use short written descriptions and simple sketches to illustrate your ideas and what other information would be required to be able to write a more complet..
The high-frequency response of a direct-coupled amplifier having a dc gain of -1000 V/V incorporates zeros at ∞and 104 rad/s (one at each frequency) and poles at 103 rad/s and 105 rad/s (one at each frequency). Write an expression for the amplifier..
Three instances (copies) of a single hierarchical circuit component made up of two AND gates, an OR gate, and an inverter are to be used. Draw the logic diagram for the hierarchical component and for the overall circuit diagram using a symbol for ..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd