Unit 2 Interpreting and Using Engineering Information

Assignment Help Civil Engineering

Reference no: EM132454612

Unit 2 Interpreting and Using Engineering Information - BTEC Level 2 Diploma In Engineering

Assessment - Engineering Drawings and Documentation

Part 1 You are given a drawing. The drawing's title is "Aligned Shaft, Date: 10/01/07"

The drawing shows a shaft connected to a base at the flange. This is identified as (A) on the individual drawings for each component.

i. Calculate the total height of the assembled components.
ii. Which size bolts are used to assemble the products and what is the tap drill size for it?
iii. If the shaft is made to its biggest diameter and the hole in the base is made to its smallest diameter, what clearance will there be between the shaft and the hole?

P1 Extract suitable information from engineering drawings and related documentation to enable a given task to be carried out.

Part 2 Study the two main components that make up the product shown in the drawing in Part 1. Identify any reasons why the product could not be made using this drawing. This may be because important information is missing.

Write down three reasons why the product could not be made because of missing or deficient information.

M1 Explain gaps or deficiencies in the information obtained that need to be resolved to enable a given Part to be carried out.

Part 3 Where you have found that information is missing from the drawing in Part 1, identify solutions.

i. Write down the solutions you have decided on for each missing piece of information and show how these should be marked on the drawing.

ii. The two sections of shaft at (B) need to be concentric with each other, within 0.02 mm. Show on the drawing how this geometric tolerance should be representeiv.

D1 Justify valid solutions to meet identified gaps or deficiencies with the information obtaineiv.

Part 4 The sketch of the electrical circuit drawing shown below needs to be converted into an electrical engineering drawing.

Research standard symbols used in electronic engineering, then produce a new circuit drawing using standard electronic component symbols.

P3 Select other information sources to support and check engineering drawings and related documentation.

Part 5 When you are working with drawing and documentation, you need to take good care of the documents.
i. Describe the care that must be taken when handling drawings, from removal from files to return to files.
ii. Describe the importance of safe storage of documents such as job cards.
iii. Describe some security features that may be used to protect documents in a drawing office.

M2 Specify the care and control procedures for the drawings and related documentation used when carrying out and checking own work output.

Unit 10: Using Computer Aided Drawing Techniques in Engineering

Assessment - CAD Drawing Using an Orthographic Projection Method

Part 1 Achieve the following UsingCAD system:

• Show how you would start up and set up the environment of the CAD system(units, toolbars, and paper size).
• Produce a standard drawing template for an engineering drawing (border, title block and logo)as shown in lectures.
• Create a folder for information storage and retrieval with name "Mechparts" and save the template in it.
• Show the steps you would take to close down the CAD system appropriately.

P1 Start up a CAD system, produce and save a standard drawing template and close down CAD hardware and software in the appropriate manner.

P7 Set up a suitable electronic folder for the storage and retrieval of information.

Part 2 According to the component shown below,produce the following, taking in consideration the showing of print screens and diagrams in the report/s:

• Construct the third angle orthographic projections of the component showing the front, side and top views.
• Write a report showing the steps of storing, retrieving and printing / plotting CAD-generated or modified drawings correctly.
• Print off a copy of a diagram.
* Dimensions and hidden details should be shown.

P2 Produce an accurate CAD drawing using an orthographic projection methoiv.

P8 Store, retrieve, print and plot CAD drawings correctly.

Part 3 Construct the first angle orthographic projections for the component shown below, taking in consideration that you have 25 minutesto accomplish the drawings, the print screens should show the steps with timesincludingthe starting-up and finishing times.

* Dimensions and hidden details should be shown.

D2 Produce detailed and accurate drawings independently and within agreed timescales.

Reference no: EM132454612

Questions Cloud

Public health in times of population crises and emergencies : What is the role of public health in times of Population Crises and Emergencies? How does the National Response Framework relate to the role of public health?

Discuss potential risks minimize risks due to mobile device : Discuss what kind of security risk exist for John Doe's business because of his home office. How can John Doe protect himself from security breaches

Engineering drawings and documentation assignment : Engineering Drawings and Documentation Assignment Help and Solution - Calculate the total height of the assembled components and Extract suitable information

Create acceptable use policy for your school computer lab : Create an Acceptable Use Policy for your school's computer lab. General Use and Ownership. Security and Proprietary Information

Unit 2 Interpreting and Using Engineering Information : Unit 2 Interpreting and Using Engineering Information Assignment Help and Solution, BTEC Level 2 Diploma In Engineering Assessment Writing Service

Identified hazards and initial risk leve : Identified hazards, initial risk level, a control measure(s) taken, approximate costs of control measure(s), and residual risk level after control measure(s)

What would you do to help create a national security culture : In 300 words, If you could, what would you do to help create a national "security culture," in which everyone is more knowledgeable and proactive about threats.

Community health concern : In regards to the chapter's title: Alcohol, Tobacco, and Other Drugs: A Community Health Concern. Why are these 3 things a community health concern?

Discuss the list two security drawbacks of virtualization : Discuss the list two security drawbacks of virtualization and the potential attacks that could be used to compromise them,researched virtualization

User Account

All Pages