Underground storage vessel

Assignment Help Mechanical Engineering
Reference no: EM13864949

1. The diagram shown below represents a process for which a pump and associated pipe work require to be correctly sized.

683_pump and associated pipe work.jpg

The liquid is to be pumped from the underground storage vessel which is vented to atmosphere (assume 1 bar pressure) to a pressurised container supported some distance above ground level. The pump is sited at ground level and must be capable of delivering 0.01 m3 s-1 with a maximum velocity of 1.8 m s-1.

(a) Calculate the theoretical diameter of the pipe; the nominal pipe diameter chosen from the table; and the actual average velocity in the nominal pipe.

Inside diameter (mm)

20

25

32

40

50

65

80

90

100

(b) Calculate Reynolds number for the process and hence the head loss due to friction. State any assumptions made.

(c) Using the following table for minor head losses, calculate the minor head losses for the system using both the equivalent length method and the number of velocity heads method. Compare the head losses estimated by each method.

Fitting

Equivalent length as number
of pipe diameters

Number of velocity
heads lost

Standard 90° bend

37

0.75

Entry to pipe

15

0.3

Exit from pipe

50

1

(d) Calculate the head required for the pump and its power requirement assuming a 70% efficiency.

(e) If the same pump was later used to pump water from the lower reservoir to the upper reservoir, what flow rate of liquid could be achieved? (N.B. This may require an iterative solution).

State any assumptions made. Data:

Liquid density, p = 960 kg m-3 Liquid viscosity, ti = 0.081 Pa s

Water density, p = 1000 kg 111-3

Water viscosity, ii = 0.001 Pa s

Reference no: EM13864949

Questions Cloud

What applicant information is not useful for selection : What information (e.g. credit score, interview, experience, etc.) did you use to select these individuals, and what weight did you use for each bit of information? (i.e. what was more important, and useful but less important) Why? What applicant ..
Businesses are faced with fixed costs : People often say that, more and more, businesses are faced with fixed costs. What evidence can you find for this? Cite a clear example (not directly from the textbook) of a cost that is becoming more fixed than it has been in the past, and give reaso..
Robert southey are generally alluded : William Wordsworth, Samuel Taylor Coleridge and Robert Southey are generally alluded to as the "what" Poets?
Evaluate the hazard and its associated risks : In a separate document of at least 500 words, explain the reasoning behind how you filled out each section of the form. Use references as needed to support the discussion - Evaluate the hazard and its associated risks, and then complete the Hazard ..
Underground storage vessel : The liquid is to be pumped from the underground storage vessel which is vented to atmosphere (assume 1 bar pressure) to a pressurised container supported some distance above ground level. The pump is sited at ground level and must be capable of de..
What were the individual family names of shakespeare''s : What were the individual family names of Shakespeare's Romeo and Juliet?
Determine projects net present value at discount rate : Determine the project’s net present value at a discount rate of 14%. Determine the project’s approximate internal rate of return. (Refer to Appendix 12B if you use the table approach) Determine the project’s payback period.
What japanese term : What Japanese term (signifying "overlay" and 'book') alludes to a book development made utilizing concertina fold, with composing/imprinting on one side of the paper?
What was the 1920s expressions gathering revolved around : What was the 1920s expressions gathering revolved around Leonard and Virginia Woolf and the area of London which gave the bunch's name?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The pressure is 100 psia and during this process the volume

a reversible carnot heat engine has 1.00 lbm of air as the working fluid. heat is received at 740 degrees f and

  Calculate the entropy generation rate for the process

Superheated steam enters one section of an open end feed water heater at 5bar and 240 c with a mass flow rate of 1 kg/s. compressed liquid water at the same pressure and 35 C enters another inlet. The mixture of these two streams leaves as a saturate..

  Determine the minimum distance d at which the brakes must

a vehicle a is stuck on the railroad tracks as a train b approaches with a speed of 120 kmh. as soon as the problem is

  If the rolling frictional force is determined to be 47500 n

1 a car with a projected frontal area of 1.8 m2 is traveling at 136 kph. if the drag coefficient of the car is 0.45 and

  Now the membrane ruptures and the water comes to a uniform

a pistoncylinder has a water volume separated in va .2m3 and vb .3m3 by a stiff membrane. the initial state in a is

  Derive taylor series expansion

Derive Taylor series expansion of f(x) = cosine(x) about the point x = 0. Write out the expression to the 6th term and then write a general expression for it for any order of Taylor series.

  The input flow rate is 3000 cubic meters per hour and the

moist air initially at 70 percent humidity and 5 c is heated to 25c. the input flow rate is 3000 cubic meters per hour

  A feedwater heater extracts steam from a turbine at 600

a feedwater heater extracts steam from a turbine at 600 kpa and 250degc which it combines with 0.3 kgs of liquid at 600

  Determine the concentration of carbon in an iron-carbon

determine the concentration of carbon in an iron-carbon alloy for which the microstructure consists of proeutectoid

  What is the ideal mechanical advantage of the wedge

A hydraulic shear applies 2000 lb force to a wedge. It is used to shear plate steel to rough size. The shear has a 1/4 inch thick cutting blade with a 45 degree slope. What is the ideal mechanical advantage of the wedge?

  Calculate the coefficient of performance of a carnot heat

an ideal vapor-compression heat pump cycle with refrigerant 134a as the working fluid provides heating at a rate of 15

  Estimate the theoretical fracture strength of a brittle

estimate the theoretical fracture strength of a brittle material if it is known that fracture occurs by the propagation

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd