Two well-insulated tanks filled with carbon monoxide

Assignment Help Mechanical Engineering
Reference no: EM13707389

Two well-insulated tanks filled with carbon monoxide (CO) gas are connected by a valve. In tank A, 1 kg of gas is stored at 100 kPa and 300 K. In tank B, 5 kg of gas are stored at 500 kPa and 870 K. The valve is opened, and the contents of the two tanks are allowed to mix until equilibrium is attained. Assuming ideal gas behavior for the carbon monoxide, determine

(a) the volume of each tank, in m^3

(b) the final temperature, in K

(c) the final pressure, in kPa

Reference no: EM13707389

Questions Cloud

Tire depends on the temperature of the air in the tire : The pressure in a tire depends on the temperature of the air in the tire. The gage pressure of an automobile tire with a volume of 0.025 m3 is measured to be 210 kPa at 25 oC at sea level on a day with calm weather. If the temperature of the air in t..
The mass flow rate of the air and exit velocity of the air : Air enters an 8” diameter pipe at atmospheric pressure at a velocity of 30 ft/s and 65 F and exits at approximately the same pressure. While in the pipe, the air passes over a heat exchanger that causes its temperature to increase by 25 F.
The initial interference required to produce : A laminated steel (E=200 GPa and nu=0.3) cylinder consists of a jacket with an inside diameter of 250mm and an outside diameter of 300mm shrunk onto a tube with an inside diameter of 150mm. The initial shrinkage pressure is 28MPa.
Energy balance-property tables and phase changes : Energy balance, property tables, phase changes. Consider water in a pot on an alien planet. You will the pot with 1.002 L (.001002 m3) of water initially at 20°C and 75 kPa (their atmospheric pressure is different than ours). How much mass is in the ..
Two well-insulated tanks filled with carbon monoxide : Two well-insulated tanks filled with carbon monoxide (CO) gas are connected by a valve. In tank A, 1 kg of gas is stored at 100 kPa and 300 K. In tank B, 5 kg of gas are stored at 500 kPa and 870 K. The valve is opened, and the contents of the two ta..
Determine the total mass of nitrogen : Determine the total mass of nitrogen (N2), in kg, required to inflate all four tires of a vehicle, each to a gage pressure of 180 kPa at a temperature of 25oC. The volume of each tire is 0.6 m^3, and the atmospheric pressure is 1 atm.
Employing the ideal gas equation of state : One kilogram of air in a piston-cylinder assembly undergoes a thermodynamic cycle consisting of three processes: Process 1-2: Constant specific volume At state 1, the temperature is 323 K, and the pressure is 1 bar. At state 2, the pressure is 2 bar...
Two-phase liquid-vapor mixture of refrigerant : A tank contains a two-phase liquid-vapor mixture of Refrigerant 134a at 10 bar. The mass of saturated liquid in the tank is 32 kg and the quality is 50%. Determine the volume of the tank, in m3, and the fraction of the total volume occupied by satura..
Kinematic viscosity : Kinematic viscosity (select all that apply)

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd