Two thermal reservoirs

Assignment Help Mechanical Engineering
Reference no: EM13720216

There are two thermal reservoirs: the hot reservoir is at 1200 K and the cold reservoir is at 600 K. If you wanted to transfer 100 kJ from on reservoir to the other, what would the change in entropy of the two reservoirs be?

Reference no: EM13720216

Questions Cloud

Using constant-specific heat theory : Twenty pounds of a gas mixture is contained in a tank with volume 30 cubic feet at 30 psia and 70 F.  The gas mixture has volumetric analysis of twenty percent carbon dioxide, thirty percent oxygen, and fifty percent nitrogen.
Determine the proper distance between compressor stations : A natural gas (methane) pipeline is to be designed to transport the gas at a rate of 50,000 scfm. The pipe is to be 6 in. ID, and the maximum pressure that the compressors can develop is 10,000 psig. The compressor stations are to be located in the p..
Evaluate how well the company has addressed : Analyze the companys value chain to determine where they can create value using the resources, capabilities, and core competencies - Determine the company''s resources, capabilities, and core competencies.
Find experimental and theoretical values idisk : Does the uncertainty in the theoretical value of Idisk account for the discrepancy in the experimental and theoretical values of Idisk
Two thermal reservoirs : There are two thermal reservoirs: the hot reservoir is at 1200 K and the cold reservoir is at 600 K. If you wanted to transfer 100 kJ from on reservoir to the other, what would the change in entropy of the two reservoirs be?
The minimum payment that the lessor is likely to accept : The tax rate is 35%, and the rate of interest is 10%. What is the maximum lease payment that the lessee company should be willing to make and the minimum payment that the lessor is likely to accept.
How long until you will be able to buy the truck : You want to purchase a new truck that will cost $18,000. You currently have $12,000. You can earn 7% interest. How long until you will be able to buy the truck?
Three payment determination bases : What are the two usual units upon which payment is based in the three payment determination bases? What is the basic difference between these two types?
Health care firm benefit from perceived higher levels : How can a health care firm benefit from perceived higher levels of quality care when fixed payment payers comprise eighty percent (80%).of the firm’s revenue?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The coeficient of discharge is 097 calculate the rate of

a ventuti meter installed in a horizantal water main of diameter 150mm has athroat diameter of75mm. the coeficient of

  Determine exit temperature of air and exit area of nozzle

Air enters a nozzle steadily at 50 psia, 140°F, and 150 ft/s and leaves at 14.7 psia and 900 ft/s. The heat loss from the nozzle is estimated to be 6.5 Btu/lbm of air flowing. The inlet area of the nozzle is 0.1 ft^2. Determine (a) The exit temperatu..

  A projectile is fired at an angle of 62deg from the

a projectile is fired at an angle of 62deg from the horizontal with a velocity of 704 ftsec. if it lands 4.75 seconds

  Air at 110 kpa and 50 c flows upward through a 6-cm-diamter

air at 110 kpa and 50 c flows upward through a 6-cm-diamter inclined duct at a rate of 45 ls. the duct diameter is then

  Assume frictionless surfaces and let g981 ms2 determine the

a block of mass 10kg moves along a surface inclined 30acircdeg relative to the horizontal. the center of gravity of the

  If the initial value of n is 1 millionl what values of k

suppose the rate of growth of a bacterial population n cellsliter is described by dndt kn -1000. the terms represent

  Air enters a set of these nozzles at 215 psia and 700

the stators in a gas turbine are designed to increase the kinetic energy of the gas passing through them adiabatically.

  Charge of melting and casting for making an alloy

Assuming that you are a process engineer in charge of melting and casting for making an alloy that consists of 40 at% Ag and 60 at% Ni. Calculate how many grams of Ag and Ni you need to weigh to make a 400-gram solder alloy with such a composition. G..

  A structural member is subjected to combined loading so

a structural member is subjected to combined loading so that the fallowing stress occur at a critical point 100 50 40

  Find the change in internal energy of the system

A fluid with a specific volume of 0.2m3 /Kg at 500KPa pressure enters a system with 8 m/s velocity. Heat losses in the system are found out to be 50 KJ/Kg of fluid supplied. The leaving pressure of the fluid is 100Kpa with a specific volume of 0.1m3 ..

  Determine the magnitude of the initial velocity

determine the magnitude of the initial velocity of the bullet and the magnitude of the force exerted by the bullet on the block.

  If the pipe is to be insulated with glass wool insulation

chilled water enters a thin shelled 4 cm diameter 200 m long pipe at 7 deg. celsius at a rate of 0.98 kgsec and leaves

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd