User Account

All Pages

Two structural members a and b are riveted to a bracket

Assignment Help Mechanical Engineering
Reference no: EM13632704

Two structural members, A and B are riveted to a bracket. Angle iron A is at 20 deg fro perpendicular with a compression force at 1600 lbs and angle iron B is at 45 deg to perpendicular and under 1200 lbs of compression. Find the resultant force and angle as they both point down to the same spot.

Reference no: EM13632704

Questions Cloud

The eccentricity is 01 the inclination is 30 degree and the : a spacecraft is in a circular equatorial orbit 1 of radius r0 and speed v0 about an unknown planet mu not equal to
A steam turbine operates with 16 mpa and 350 degree c : a steam turbine operates with 1.6 mpa and 350 degree c steam at its inlet and saturated vapor at 30 degree c at its
A pulley of radius 03 m is rotating counter-clockwise and : 1. a pulley of radius 0.3 m is rotating counter-clockwise and is pulling a weight upward. the weight slows the spinning
The free convection heat transfer coefficient on a thin hot : the free convection heat transfer coefficient on a thin hot vertical plate suspended in still air can be determined
Two structural members a and b are riveted to a bracket : two structural members a and b are riveted to a bracket. angle iron a is at 20 deg fro perpendicular with a compression
If the management decided to use the standard hour plan as : in a workshop three workers are doing similar continuous work which is turning and threading a cylindrical steel bar. a
In a mechanical coal-washing process a portion of the : in a mechanical coal-washing process a portion of the inorganic sulfur and ash material in the mined coal can be
A pipeline has been proposed to carry natural gas 1715 : a pipeline has been proposed to carry natural gas 1715 miles fro alaskas north slope to calgary alberta canada. the
When the rope is at an angle of a 20 the 05 kg sphere a : when the rope is at an angle of a 20? the 0.5 kg sphere a has a speed v0 1.2 ms. the coefficient of restitution

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the density and specific volume of carbon

determine the density and specific volume of carbon monoxide at a pressure 100 kpa and a temperature of 300 k. for co

  Air enters a set of these nozzles at 200 psia and 695

the stators in a gas turbine are designed to increase the kinetic energy of the gas passing though them adiabatically.

  Determine p2 v2 and t2 for the trapped air in the final

a u-tube manometer is closed on the left end and open to the atmosphere on the right end where patm 105 pa. the

  Will this specimen experience fracture if the largest

a specimen of a 4340 steel alloy having a plane strain fracture toughness of 45 mpa m is exposed to a stress of 1000

  What stresses are produced in the bolt and in the tube if

a 0.5-in.-diameter steel e 30000 ksi bolt 1 is placed in a copper tube 2 as shown in fig. p5.47. the copper e 16000

  Use entropy balance for a closed system to determine

use entropy balance for a closed system to determine whether the entropy change of the following processes is positive

  Find omega3 va vb and vc of the mechanism below using the

find omega3 va vb and vc of the mechanism below using the instant center graphical method. develop the linear graph and

  Estimate the diameter of an aluminum atom given that the

estimate the diameter of an aluminum atom given that the density is 2.7 gramscubic centimeter and the atomic mass is

  Gold foil is 008 mm thick and 670mm2 in area a it is cubic

gold foil is 0.08 mm thick and 670mm2 in area. a it is cubic with a0.4076nm. how many unit cells are there in the foil?

  Nitrogen gas at 60 kpa and 7deg c enters an adiabatic

nitrogen gas at 60 kpa and 7deg c enters an adiabatic diffuser steadily with a velocity of 275 ms and leaves at 85 kpa

  Turbofan engine on a test stand in the maintenance

The explanation provided below, provide the solution to the problem in simple and easy to understand steps. A turbofan engine on a test stand in the maintenance shop is being run at a continuous setting of 22,700 lbs of thrust. The TSFC is 0.5 lbs/..

  Calculate the highest velocityacceleration and jerk that

a cam is to be desinged for an automated part loader.using the motion equationsconstruct a chart that tabulates

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd