Two mass are connected by a light inextensible cord

Assignment Help Mechanical Engineering
Reference no: EM13720649

Two mass are connected by a light inextensible cord that passes over a homogeneous 4-kg cylinder having a diameter of 1200 mm. How long will it take the 7-kg mass to move from rest to a speed of 2 m/s^2

NOTE: imagine a cylinder with a spring around it with end holding a block with mass 5-kg and the other 7-kg

Reference no: EM13720649

Questions Cloud

Design a reservoir for industrial machine tool application : Design a reservoir for an industrial machine tool application. The machine runs continuously for 8 hours a day. The pump delivers 20 gpm with no heat exchanger in the circuit. The components and lines hold 5 gallons of fluid. (Note: .134 ft^3= I gall..
Calculate the potential emissions of toluene : A stream of gas flowing at 15,000 scfm contains 20 ppm of toluene. Assuming the process operates 8500 hours per year, calculate the potential emissions of toluene, tons/year. What kind of a system should be considered to control this stream, and why?
Estimate the nominal size of the smallest SAE Grade : Estimate the nominal size of the smallest SAE Grade 1 standard UNC bolt that will not yield under a tightening torque of 1000 in-lb. Neglect stress concentration.
How high will the ball rise after its second bunch : A ball is dropped from a height of 1.0m, bounces off the floor and is observed to rise up a maximum height of .8 m. How high will the ball rise after its second bunch?
Two mass are connected by a light inextensible cord : Two mass are connected by a light inextensible cord that passes over a homogeneous 4-kg cylinder having a diameter of 1200 mm. How long will it take the 7-kg mass to move from rest to a speed of 2 m/s^2
Derive the general kirsch equation : The following stress state exists around a wellbore drilled in the Atlantic Ocean: sigma x = sigma y = 80 bar   sigma zz = 100 bar    tau xy = tau xz = tau yz = 0   Pw = 80 bar. Derive the general Kirsch equation (Aaddnoy version)
Discuss how you would solve this problem using gas tables : Twenty pounds of a gas mixture is contained in a tank with volume 30 cubic feet at 30 psia and 70 F.  The gas mixture has volumetric analysis of twenty percent carbon dioxide, thirty percent oxygen, and fifty percent nitrogen. Discuss how you would s..
Number of rubber molecules per unit volume : Calculate the Gibbs free energy change of a rubber band stretched to 5 times its original length with concurrent contractions in its other two dimensions of 2.24 times at 25 C. The number of rubber molecules per unit volume, N, for a typical rubber i..
Determine the minimum beam height-mass of beam : A new cylindrical tank is being designed for SeaWorld, where the 3m high Plexiglass wall will be supported using I-beams spaced 2m apart. The beams are to be constructed from 13mm steel plate (t=b) having a yield strength of 250MPa. This design shoul..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd