Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
This project is about building a coded lock system using ATmega8 by using assembler language. LCD should show your name on the first line and on the second line it should show enter code and when you enter code it should there and if you enter the right code it should say "welcome" also it should turn on one led. " The following needs to be presented:
Let Xa (jΩ) denote the Continous Time FourierTransform of a real-valued continuous time functionxa(t). Show that the magnitude spectrum | Xa(jΩ) | is an even function of Ω and the phase spectrumθ(Ω) = arg{Xa (jΩ)} is an odd function ofΩ.
Four point charges of 1 C are located at the corners of a square with a side a =1 m. Find the magnitude of the force experienced by each charge.
A 600 V, dc shunt motor has armature and field resistance of 15 ohms and 600 ohms respectively. When the motor runs unloaded, the ine current is 3 A, and the speed is 1000rpm. Calculate the developed torque at a full load armature current of 50 A.
What is the value of beta after the following code executes if the input is 5 int beta; cin >> beta; switch(beta){ case 5: beta += 5; case 1: beta++; case 5: beta += 5; break; case 4: beta += 4; }
Explain why the low value (0) for the 'output' of a digital logic gate is lower than the low value for the 'input' of a digital logic gate (This is the case for CMOS and Bipolar logic). Look at a specsheet.
A telecommunication system has a link bandwidth of 10 MHZ, signal propagation of 3.5 x 10^8 m/s, transmitting as 1500 frames per minute, with 15000 bits per frame, over a distance of 100 km. What is the bandwidth-delay product?
Design a garage door controller using PLC Ladder Diagram (RSLOGIX 500 PLC SIMULATOR). The behavior of the garage door controller is as follows there is a single button in the garage, and a single button remote control.
Write a Matlab script file that uses the function from Part 1 to apply "water filling" for distributing total power P = 10 over N = 5 parallel channels with noise levels x = [2, 3, 1, 6, 4] and that plots the noise and power distribution over the ..
The normalized lowpass filter with a cutoff frequency of 1 rad/sec is given as Hp(s) 1/s+1. Use Hp(s) and the BLT to obtain an corresponding IIR digital high passs filter with a cutoff of 30 Hz, assuming a sampling rate of 200 hz,
The efficiency and power factor for these conditions are 85 and 90% respectively. The combined windage, friction, and stray power losses are 1011W, the rotor conduction losses are 969W, and the stator conductor losses are 1559W.
a.) Determine where the given poles are mapped into the z-plane.b.) How would you determine if these poles are mapped inside, on, or outside the unit circle in the z-plane. Explain.
The receiver is designed to receive transmitted signals between 5 MHz and 25 MHz. High-side tuning is to be used. Determine the tuning range and tuning ratio of the local oscillator if the IF frequency is 400 kHz and 2 MHz, respectively.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd