User Account

All Pages

This part is to withstand a fluctuating tensile load

Assignment Help Mechanical Engineering
Reference no: EM13630121

A 1.5 in-diameter bar has been machined from a steel 1050 (Su = 100ksi Sy = 84ksi). This part is to withstand a fluctuating tensile load varying from 0 to 20 ksi. The surface is mirror polished.

a) Find the factor of safety guarding against first-cycle yield.

b) Find the factor of safety guarding against fatigue.

Reference no: EM13630121

Questions Cloud

A plate of mass m is suspended between two opposing jets : a plate of mass m is suspended between two opposing jets each of area a velocity vo and density d. the plate is
The arm of a car windshield wiper is 1275 inches long and : the arm of a car windshield wiper is 12.75 inches long and is attached at the middle of 15.00 inch blade assume that
What is the maximum possible temperature of the high : a refrigerator cycle has a cop of 3 and removes 100kw of heat from a building which is kept at 23c. the device rejects
A robot is on the surface of mars the angle of the : a robot is on the surface of mars. the angle of the depression from a camera in the robot to a rock on the surface of
This part is to withstand a fluctuating tensile load : a 1.5 in-diameter bar has been machined from a steel 1050 su 100ksi sy 84ksi. this part is to withstand a fluctuating
As observed by the juggler what is the balls total time of : a juggler traveling in a train on level track throws a ball straight up relative to the train with a speed of 6.65 ms.
5 kg of water at 1 atm in a cylinder was heated until it is : 5 kg of water at 1 atm in a cylinder was heated until it is half boiled.1 what is the atm inside the cylinder?2 the
Boral is a commercial shielding material consisting of : boral is a commercial shielding material consisting of approximately equal parts by weight of boron carbide b4c and
A similar one-week study with mountain communications : there are two major internet providers in the colorado springs colorado area one called htc and the other mountain

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Steam enters a turbine with a pressure of 3000 kpa a

steam enters a turbine with a pressure of 3000 kpa a temperature of 400 degrees c and a velocity of 160 msec. steam

  What size unf bolt made from sae grade 5 steel is needed to

what size unf bolt made from sae grade 5 steel is needed to carry a static tensile load of 3000lb with a safety factor

  The vale is open and the two gases are allowed to mix

two tanks a and b are connected by a short section of pipe with a valve that is initially closed. both tanks are

  A rigid insulated vessel is divided into two compartments

a rigid insulated vessel is divided into two compartments connected by a valve. initially one compartment occupying

  A 40 mm diameter hole is drilled 3 m deep into the steel

a 40 mm diameter hole is drilled 3 m deep into the steel shaft. when the two torque are applied determine a the maximum

  The engine exit as well as the inefficiencies of engine

consider an aircraft powered by a turbojet engine that has a pressure ratio of 9. the aircraft is stationary on the

  The third law entropy for gas at stp is 270 jkmole

one mole of ideal monoatomic gas undergoes an irreversible adiabatic process in which gas ends up at stp and for which

  2 kg of water is contained in the vertical frictionless

2 kg of water is contained in the vertical frictionless piston cylinde device.the mass of the piston is such that the

  An air cored solenoid has 100 turns of wire the core has a

an air cored solenoid has 100 turns of wire the core has a diameter of 2cm and the length of the winding over the core

  The rod is in an air environment with tinfinity 20 degree

a brass rod 100 mm long and 5 mm in diameter extends horizontally from a casting at 200 degree c. the rod is in an air

  Calculate the angular separation between the first order

Calculate the angular separation between the first order minima on either side of the central maxima when the slit has a width of 6x10-4 cm & light illuminating it has a wavelength of 6000A0?

  If we want to produce the same total power with our current

the average idle human releases about 116 w of power which corresponds to a daily consumption of 2400 calories. at

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd