User Account

All Pages

This member is to be designed according to maximum shear

Assignment Help Mechanical Engineering
Reference no: EM13612629

A solid square cross-sectional bar (bxb) with a yield stress of 250 MPa is subjected to a compressive axial force, P = 140 kN acting at the centroid of the section and a torque T = 20 kN.m. This member is to be designed according to maximum shear stress criterion, with a safety factor of 2.

a) What is the minimum allowable cross-sectional dimension, b?

b) What would your answer be if the load was acting parallel to the surface instead of normal to it?

Reference no: EM13612629

Questions Cloud

Determine the absolute pressure of the water at the ground : the water level in a sealed tank is 26 m above the ground. the pressure in the air space above the water is 0.25 mpa
The gap between the two plates is h 0005 m the fluid has a : there is flow between two plates as shown in the schematic. the bottom plate is stationary. the top plate is moving at
Hydrogen at 25 bar 450degc enters an adiabatic turbine and : hydrogen at 25 bar 450degc enters an adiabatic turbine and expands to 2 bar 160degc with a mass flow rate of 0.2 kgs.
Determine a the temperature of the refrigerant exiting the : refrigerant 134a at -10degc 1.4 bar and a mass flow rate of 280 kghr enters an insulated compressor operating at steady
This member is to be designed according to maximum shear : a solid square cross-sectional bar bxb with a yield stress of 250 mpa is subjected to a compressive axial force p 140
Determine the power kw for the compressor if the inlet : air enters an adiabatic compressor at 197 kpa and 316 k and exits at a temperature of 508 k. determine the power kw for
Perform the appropriate post hoc comparisons what do you : in a study in which k 3 n 21 mean of x1 45.3 mean of x2 16.9 and mean of x3 8.2 you compute the following sums of
A the exit the pressure and quality are 200 kpa and 066 : steam enters an insulated turbine at 100 bar 400oc. at the exit the pressure and quality are 200 kpa and 0.66
Derive the probability distribution for total losses under : kilgallen inc. has the total inventory of 1000. currently kilgallen has this entire inventory stored in one warehouse.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the failure envelope and the non-failure region

Determine the failure envelope and the non-failure region in the sigma_y - tau_xy plane using Tsai-Hill theory for the following cases

  Determine a the maximum temperature in the cycle the net

a four-cylinder four-stroke 2.8-liter compression-ignition engine operates on the ideal dual cycle with a compression

  Solve for the dynamics of the resulting system

Solve for the dynamics of the resulting system for 20 seconds of real time using midpoint method.

  Define the final state inside the tank

Find the final state inside the tank, A tank contains 2kg of nitrogen at 10K with a quality of 50%.Through a volume flow meter and valve, 0.5kg is now removed while the temperature remains constant.

  The molar heat capacity of liquid iron exceeds that of iron

the molar heat capacity of liquid iron exceeds that of iron vapor by 2.5222calkthe molar heat of evaporation of liquid

  Determine the smallest horizontal force required

Determine the smallest horizontal force required to lift the 260- crate. The coefficient of static friction at all contacting surfaces is = 0.7. Neglect the mass of the wedge.

  Locate the initial and final states on a sketches

water contained in a closed, rigid tank, initially saturated vapor at 200C, is cooled to 100C. determine the initial and final pressure, each in bar. locate the initial and final states on a sketches of the p-v and T-v digrams.

  What stress is requireed to strain a sample

How much work(J)is done in a natural rubber filament when strains slowly and non reversely to a= 2?

  Iron has a bcc crystal structure an atomic radius of 0124

a iron has a bcc crystal structure an atomic radius of 0.124 nm and an atomic weight of 55.85 gmol. compute and compare

  The boron fibers are produced with a 125 mum diameter

a metal matrix composite mmc is made of a 2024 al alloy matrix and continuous nbspboron fibers. the boron fibers are

  Explain why the component does not accelerate down through

a robot unloads a finished component from a machine and places it on a gravity conveyor. the conveyor accelerates from

  A packed bed is composed of crushed rock with a density of

a packed bed is composed of crushed rock with a density of 175 lbmft3nbspof such anbspsize and shape that the average

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd