The wire in a heating element of an electric stove burner

Assignment Help Physics
Reference no: EM13641718

The wire in a heating element of an electric stove burner has a 0.75-m effective length and a 2.0*10^-6 m cross-section area. The wire is made of iron.

(a) What is its resistance when the stove is off (ie. 20 degree C)?

(b) When on, it operates at a 370 degree C temp. What is its operating resistance?

Reference no: EM13641718

Questions Cloud

Consider the following give your answers correct to two : consider the following. give your answers correct to two decimal places.a find the standard score z such that the area
What is the total heat transfer rate watts from the pipe : a horizontal stainless steel conductivity k 15 wmk circular pipe of outside and inside diameters of 0.50 m and 0.45 m
The magnitude of the force on q1 due to q2 equals the : two charges are placed between the plates of a parallel plate capacitor. one charge is q1 and the other is q2 5.20
A temperature of 38oc at the beginning of compression the : a four-cylinder four-stroke internal combustion engine has a bore of 6.5 cm and a stroke of 5.3 cm. the clearance
The wire in a heating element of an electric stove burner : the wire in a heating element of an electric stove burner has a 0.75-m effective length and a 2.010-6 m cross-section
Determine the mass flow rate of condenser cooling water if : water is the working fluid in an ideal rankine cycle. the steam enters the turbine at 15 mpa and enters the condenser
What is the magnitude and direction of the force that must : you are swinging your younger sister in a horizontal circle of radius 0.80 m. her mass is 21 kg and you arrange it so
A 047 kg object connected to a light spring with a force : a 0.47 kg object connected to a light spring with a force constant of 22.0 nm oscillates on a frictionless horizontal
Analyze the cycle assuming air standard assumptions that : a gas turbine engine has a pressure ratio of 9.2 to 1 and operates on an ideal brayton cycle. assume air enters at 25 c

Reviews

Write a Review

Physics Questions & Answers

  Calculate what is the final charge on the shell

three concentric conducting spherical shells have radii a, b, and c such that a

  What is the ratio of the velocities of the fragments

A popcorn kernel initially at rest explodes into two pieces, one piece having twice the mass of the other. What is the ratio of the velocities of the fragments

  Golf ball is driven from the tee with an initial speed

A 47.0g golf ball is driven from the tee with an initial speed of 52.0 m/s and rises to a height of 24.6 m. neglect air resistance and determine the kinetic energy of the ball at its highest point.

  Determine the volume of the paint

A partly-full paint can has 0.82 U.S. gallons of paint left in it. What is the volume of the paint

  The piston and plunger are at the same height and each has

the drawing shows a hydraulic chamber in which a spring spring constant1600nm is attaches to the input piston and a

  Estimate what is the final angular momentum of the system

A uniform disk has a mass of 4.6 kg and a radius of 0.2 m. The disk is mounted on frictionless bearings and is used as a turntable. What is the final angular momentum of the system

  What is the minimum speed of the car

In a loop-the-loop ride a car goes around a vertical, circular loop at a constant speed. The car has a mass m = 222.0 kg and moves with speed v = 16.16 m/s. What is the minimum speed of the car

  At what point does the ball have maximum speed

A toy cannon uses a spring to project a 5.30 g soft rubber ball. The spring is originally compressed by 5.00 cm, At what point does the ball have maximum speed

  What direction is the bolt deflected by earth magnetic field

A lightning bolt consisting of electrons moves from the cloud to the ground near the equator. What direction is the bolt deflected by the Earth's magnetic field

  A 154 wide 134 high 1400 car hits a very slick patch of ice

a 1.54 wide 1.34 high 1400 car hits a very slick patch of ice while going 20.0 . air resistance is not negligible. if

  Determine the required string tension

A university physics department buys 100m of string and determines its total mass to be 0.150kg. what is the required string tension

  What tension must the string be placed

suppose the apparatus as used in this lab: A cube of mass M = 500 g and side length 30 mm is free to spin on an axis through the center of one face. A massless pulley on this axis has a diameter of 2r = 10 mm. An object with m = 50 g is hung from ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd